TechPB Forum: GoG eXTCy first shot bolt stick - TechPB Forum

Jump to content

Page 1 of 1

You cannot start a new topic
You cannot reply to this topic

GoG eXTCy first shot bolt stick

#1 AtomicAdrian

Hiding in back center

Group: Members
Posts: 733
Joined: 09-November 10
Gender:Male
Location:Mesquite, TX

Posted 21 February 2013 - 10:33 PM

After my eXTCy has been idle for about 10-15 minutes, the bolt sticks after the first shot I fire/dry fire. I've messed with the settings a bit and it doesn't seem to go away unless my dwell is abnormally high (40 or so). Right now my dwell is set to 35 and my FSDO comp is set to 15.

Also, the manual is a bit confusing; it says that the stock setting for FSDO comp is 20 ms, but the setting only goes from 0 to 15 ms. Can anyone help?

I suck at paintball.
R.I.P BORG, ONE OF MY PAINTBALL HEROES.
B/S/T feedback: 9/0/0

#2 PassivePB

Member

Group: Members
Posts: 75
Joined: 26-January 12
Gender:Male
Location:Canuckistan

Posted 22 February 2013 - 12:18 AM

Use a thinner lube, or less lube. Little = More with spoolies

#3 TacticlTwinkie

*insert witty title*

Group: Members
Posts: 3,625
Joined: 02-August 11
Gender:Male
Location:Surf City, USA

Posted 22 February 2013 - 12:24 AM

That gun likes to be lubed lightly, but more often. You might be over lubing it. I like to do mine every other case, and just enough so the orings look wet. If you cake it in there it will gum it up, causing your problem.

BST Feedback: 4/0/0

#4 Soundwave

I win paintball.

Group: TechPB Players Club
Posts: 638
Joined: 11-February 10
Gender:Male
Location:Melbourne, Australia

Posted 22 February 2013 - 10:11 AM

Whenever you get first shot drop, the first step is always to remove the bolt and clean everything off. Lube will sometimes become sticky under certain circumstances, and it's always important to remove any old lube that may be causing problems before you re-lube it.

Next, I'd like you to reset your board to factory settings.

Re-lube your bolt using a very thin lubricant, and also replace your battery.

If all of that doesn't fix it, just come back and I'll get you shooting again

My Moderator Application: http://www.techpb.co...howtopic=196721

#5 AtomicAdrian

Hiding in back center

Group: Members
Posts: 733
Joined: 09-November 10
Gender:Male
Location:Mesquite, TX

Posted 23 February 2013 - 11:40 PM

Cleaned and re-lubed with a thin amount of hatersauce, factory reset board, fresh battery. Set the dwell to 27ms for HPA as per the manual (it's factory set to use CO2). Sitting here indoors, gun won't cycle fully.

This post has been edited by AtomicAdrian: 23 February 2013 - 11:50 PM

I suck at paintball.
R.I.P BORG, ONE OF MY PAINTBALL HEROES.
B/S/T feedback: 9/0/0

#6 Soundwave

I win paintball.

Group: TechPB Players Club
Posts: 638
Joined: 11-February 10
Gender:Male
Location:Melbourne, Australia

Posted 25 February 2013 - 06:53 AM

Ok, is it not cycling fully on the first shot, or is it not cycling fully at all?

My Moderator Application: http://www.techpb.co...howtopic=196721

#7 AtomicAdrian

Hiding in back center

Group: Members
Posts: 733
Joined: 09-November 10
Gender:Male
Location:Mesquite, TX

Posted 25 February 2013 - 01:49 PM

Not cycling fully at all. Bolt moves all the way forward and all the way back, but doesn't dump enough air for the actual shot. The gun works alright with the dwell set at 35ms, however.

I suck at paintball.
R.I.P BORG, ONE OF MY PAINTBALL HEROES.
B/S/T feedback: 9/0/0

#8 Danny D

Senior Member

Group: Members
Posts: 1,981
Joined: 01-March 10
Gender:Male
Location:Canada

Posted 25 February 2013 - 08:52 PM

Sounds like a battery problem to me. Use fresh duracell or energiser only. Looks like your battery is on the fritz.

Lube bolt like this:

Use grease:
Posted Image