[dirtyp]

Got some cocker threaded barrels? In the pic of various barrels what is the one with the .697 on it?

[brycelarson]

here's a list of barrels I currently have for sale:

http://www.techpb.co...howtopic=105627

many are cocker threaded.

[roshkehba]

can it be done on this? the thinnest part on the barrel are thicker then the freak insert

[brycelarson]

roshkehba, on 26 October 2010 - 02:13 PM, said:

can it be done on this? the thinnest part on the barrel are thicker then the freak insert
http://i296.photobuc...pv/100_2182.jpg

looks like it would be fine. Can't gaurantee the strength of the barrel after I do - but yeah, should be able to.

[EricCartman]

what wouuld be the smallest freak bore that you would recommend for the phantom barrel

[brycelarson]

EricCartman, on 14 November 2010 - 11:57 AM, said:

what wouuld be the smallest freak bore that you would recommend for the phantom barrel

smallest freak insert? depends on your paint.

[EricCartman]

its marbs about .689 ish

[brycelarson]

EricCartman, on 14 November 2010 - 10:06 PM, said:

its marbs about .689 ish

.003-.005 is absolutely safe - that means .684 would be a great choice. that's big paint compared to what I'm used to seeing - you sure it's that big?

[TMSballer]

Ok I got some barrels that I will trade and I'd like bored I'll post in your other thread too but pick what you want some of the barrels I would just like to trade for different colors or something along those lines. I'm not sure if you have what I'm asking or can do what I'm asking just thought I would offer and see what you say.

Stock spyder Imagine Barrel(silver)
Stock pilot Barrel (red) (would like freak bored)
Stock MR2 Barrel (black)
RAP4 tactical barrel W/ silencer (black)
Spyder Threaded

Freak Jr. W/ 3 inserts
stock Ion barrel
Ion threaded

Freak Jr.Barrel, I would like to traded for a dust freak jr barrel. (not sure if you have theses)
15 inch Lucky barrel .689 bore (trade For A blue Barrel Freaked or Cp)
Stock G3 Barrel

Cocker threaded

Stock ACI Maverick Barrel (would like freaked)
ACI threaded

Stock Phantom Barrel (would like freaked)
Phantom Threaded

Thanks,
TMS

[brycelarson]

TMS - I don't want to do the spyder barrels - too close to the size of a freak insert.
I can bore the stock Ion barrel if you want.
How long is the back on the Lucky barrel?
I can bore the stock G3 barrel.
I don't want to attempt the maverick barrel - also too close.
I can bore the phantom barrel.

It's $30 a barrel for boring plus the cost of return shipping. Which do you want to have bored and what barrels do you want to trade for the service? I will take any barrel that I listed as something I can bore.

[EricCartman]

yes im sure. i even emailed them to double check. itss cpx sports marbs

[t51rmkiv]

Have you attempted to do a .693 bore planet eclipse barrel yet?

[brycelarson]

t51rmkiv, on 15 November 2010 - 04:49 PM, said:

Have you attempted to do a .693 bore planet eclipse barrel yet?

don't think so - take a picture and let me look at it.

[The_Economist]

brycelarson, on 15 November 2010 - 04:54 PM, said:

t51rmkiv, on 15 November 2010 - 04:49 PM, said:

Have you attempted to do a .693 bore planet eclipse barrel yet?

don't think so - take a picture and let me look at it.

Yeah, if you could bore out my .693 back from my stock ego barrel I would definitely jump on that. I'll take some pics tonight if I can remember.

[The_Economist]

I remembered!

Shaft 3 back length is 7 3/16".
OD on the thinnest part in the middle where it tapers in is 13/16ths.
OD on the part in the back where it threads into the gun is also 13/16ths.
ID is 11/16ths.
There's still about an inch of control bore that extends past the length of a freak insert before the bore for the front threads starts.

This post has been edited by The_Economist: 15 November 2010 - 07:05 PM

[t51rmkiv]

The_Economist, on 15 November 2010 - 07:03 PM, said:

I remembered!

Shaft 3 back length is 7 3/16".
OD on the thinnest part in the middle where it tapers in is 13/16ths.
OD on the part in the back where it threads into the gun is also 13/16ths.
ID is 11/16ths.
There's still about an inch of control bore that extends past the length of a freak insert before the bore for the front threads starts.

Lol, beat to the punch....even the same color.

[brycelarson]

should be doable. just a bit tricky to grab in the lathe since it doesn't have any good cylindrical spots. yeah, I think I would be willing to try.

[The_Economist]

T51rmkiv, you have excellent taste.

Bryce, how shall shall I ship it to you or do you want me to wait? PM me with details if you prefer.

[t51rmkiv]

The_Economist, on 16 November 2010 - 12:14 AM, said:

T51rmkiv, you have excellent taste.

Bryce, how shall shall I ship it to you or do you want me to wait? PM me with details if you prefer.

Ditto...also how would you feel about some Cocker maintenance? I have a Docs Fastback with MQ in dyer need of TLC.

[shutts67]

Quick question/possible suggestion:

Are the TechPB barrels Apex-able? They are only like $13 right now.