Marq Rapper

Marq Rapper It appears that my Rapper has a Ryujin board in it from the factory?

#1 Sledwrecker

Newbie

Group: Members
Posts: 11
Joined: 21-August 11

Posted 24 January 2013 - 12:24 AM

Is this common? Can anyone tell me more about it? Possibly settings, or setups that would give me a good starting point. Also positives and negatives of this board? I'm new to the BL family, and really like my Rapper, just want to know more about it, and how to fine tune it.

Thanks!

#2 andrewthewookie

Pull start me and I'm yours ;)

Group: Moderator
Posts: 19,691
Joined: 22-August 09
Gender:Female
Location:Your bedroom

Posted 24 January 2013 - 12:29 AM

If you're looking to fine tune it, I'd recommend getting a pressure tester, as that will allow you to make sure that when you do mess around with the LPR, you can get it back to recommended ranges if it starts acting up. For a Marq, I'd say the best setup is the stock settings. You can tweak it a bit, but they like to run the best at recommended pressures. I am unfamiliar with the board, but if it has the modes you need, then it should be good to go.

This post has been edited by andrewthewookie: 24 January 2013 - 12:29 AM

Hybrid SFT • 09 Impulse • HB REV-i • Macroless Mech Ion
Rotor • Grillz • PE 70/45 • Feedback - 21/0/0
Fear is the mind-killer

#3 bigschank

Sophomore Member

Group: Members
Posts: 491
Joined: 02-October 08
Gender:Male
Location:Central Florida

Posted 09 February 2013 - 05:09 AM

If you are unsure of the board settings and since BLAST doesn't have the marq manuals on there site, I would just give them a call. Know what type of engine you have in your Rapper, cause that might mean slight differences in the board settings and pressures. But they are always very nice and helpful. Whenever I call, it always seems I get Zack. Kinda cool to be talking to Bob's son! and Welcome to the Bob Long Fan Boy Club! lol

Feedback: +5/0

#4 Sledwrecker

Newbie

Group: Members
Posts: 11
Joined: 21-August 11

Posted 09 February 2013 - 10:17 AM

Thanks guys! I do have the pressure tester, and my pressures are within the recommended specs, I called BL, and they said I have the Frenzy 4.0 board, but the instructions I've found online don't seem to work on this board. I will mess with it a bit more, if that fails, then Virtue OLED, here I come!

).
Thanks again!

#5 bigschank

Sophomore Member

Group: Members
Posts: 491
Joined: 02-October 08
Gender:Male
Location:Central Florida

Posted 09 February 2013 - 11:20 AM

Save some money and get a tadao instead. Tadao Oled for 160 bnib

Feedback: +5/0

#6 Sin_Ister611

Dude with a gun

Group: Members
Posts: 632
Joined: 21-November 10
Gender:Male
Location:Kansas

Posted 15 February 2013 - 02:55 PM

http://playpaintball...nstructions.pdf

Everything you'll need to know it right there ^^^^

As soon as I buy or trade for a marker and it doesn't have a manual, I immediately go print off the manual for the marker and the board manual if it's there usually before I even get the goods. Also if you have an android, dunno about iphone, but get the markerhelpfree app and for the most part you will have any manual for any marker and board on your phone. Note** Ryujin boards are in the Bob Long manual section.

This post has been edited by Sin_Ister611: 15 February 2013 - 02:59 PM