TechPB Forum: TechT Bolt vs. Billy wing Bolt - TechPB Forum

Jump to content

Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

TechT Bolt vs. Billy wing Bolt

Poll: TechT Bolt vs. Billy wing Bolt (11 member(s) have cast votes)

WHICH ONE

  1. Billy Wing Bolt (4 votes [40.00%])

    Percentage of vote: 40.00%

  2. Techt Bolt (6 votes [60.00%])

    Percentage of vote: 60.00%

Vote Guests cannot vote

#1 User is offline   ironmenpaintball12 

  • Member
  • PipPip
  • Group: Members
  • Posts: 57
  • Joined: 30-September 08
  • Gender:Male
  • Location:oxnard,ca

Posted 15 September 2010 - 11:02 PM

ok so i hae a dm7 and i wanted to know whih bolt is better the TechT Bolt or the Billy wing bolt. And should i get the dye hyper3 reg or keep the hyper2 reg.
Proud owner of a DM7

#2 User is offline   sticktodrum 

  • Paintball's Lovable Prince Of Parody
  • PipPipPipPipPipPipPipPip
  • Group: Players Club
  • Posts: 11,892
  • Joined: 09-December 08
  • Gender:Male
  • Location:Queens, NYC


Posted 15 September 2010 - 11:08 PM

Don't get either bolt. Also, don't change the regulator. Everything you have on your DM is perfect, please don't waste your money.
Gerber, Surefire, TOPS, and Cold Steel all suck the big one. Buy quality products, not junk. :-)

#3 User is offline   ironmenpaintball12 

  • Member
  • PipPip
  • Group: Members
  • Posts: 57
  • Joined: 30-September 08
  • Gender:Male
  • Location:oxnard,ca

Posted 15 September 2010 - 11:13 PM

View Poststicktodrum, on 15 September 2010 - 11:08 PM, said:

Don't get either bolt. Also, don't change the regulator. Everything you have on your DM is perfect, please don't waste your money.

k thanks
Proud owner of a DM7

#4 User is offline   chewiestmonkey 

  • Master Member
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 2,943
  • Joined: 26-September 08
  • Gender:Male
  • Location:Bitch'n Montana

Posted 19 September 2010 - 01:34 AM

yeah, keep it stock.
fine tune the dwell and lpr and call it good ;]
My BST feedback thread: http://www.techpb.co...&mode=show&st=0
If you'r too busy getting even, you will never get ahead.

#5 User is offline   ironmenpaintball12 

  • Member
  • PipPip
  • Group: Members
  • Posts: 57
  • Joined: 30-September 08
  • Gender:Male
  • Location:oxnard,ca

Posted 19 September 2010 - 06:37 PM

View Postchewiestmonkey, on 19 September 2010 - 01:34 AM, said:

yeah, keep it stock.
fine tune the dwell and lpr and call it good ;]

What are the best setting for the gun then?it shoots good but i want it to be at its best.
Proud owner of a DM7

#6 User is offline   chewiestmonkey 

  • Master Member
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 2,943
  • Joined: 26-September 08
  • Gender:Male
  • Location:Bitch'n Montana

Posted 19 September 2010 - 09:02 PM

View Postironmenpaintball12, on 19 September 2010 - 06:37 PM, said:

View Postchewiestmonkey, on 19 September 2010 - 01:34 AM, said:

yeah, keep it stock.
fine tune the dwell and lpr and call it good ;]

What are the best setting for the gun then?it shoots good but i want it to be at its best.



What I basicly did was raise the dwell and lowered the Lpr.
it will make it shoot very very nice.
My BST feedback thread: http://www.techpb.co...&mode=show&st=0
If you'r too busy getting even, you will never get ahead.

#7 User is offline   shft105 

  • Newbie
  • Pip
  • Group: Members
  • Posts: 6
  • Joined: 09-February 13

Posted 22 February 2013 - 10:49 PM

Would you say the same thing applies to a PM8?

#8 User is offline   TheGunTech 

  • Newbie
  • Pip
  • Group: Members
  • Posts: 22
  • Joined: 22-February 13

Posted 23 February 2013 - 09:36 PM

Neither. Keep your reg. It will need to be rebuilt soon, though.

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users