Km Speedfeed?

#1 Garribean

Sophomore Member

Group: Members
Posts: 655
Joined: 15-December 12
Gender:Male

Posted 30 December 2012 - 07:05 PM

How good is the KM Rotor Spine Feed? I'm looking into a speedfeed and this is the cheapest one. lol
Would anyone who has it, recommend it?

My link

HD-PVR For Sale/Trade!
HD-PVR
Stuff Below!
Stock, Remoteline,& Paint!

#2 lukylovespaintballin

Turtleloverofthemaxofthemostextreme

Group: Members
Posts: 1,306
Joined: 17-April 11
Gender:Male

Posted 30 December 2012 - 07:34 PM

had it on my rotor a while ago, it is ok, kept balls in and droped in after a day of play from 2 inches

This post has been edited by lukylovespaintballin: 30 December 2012 - 07:34 PM

My link for my guns

MY FEEDBACK 5/0/0

canscom, on 13 December 2012 - 11:17 PM, said:

Nothing some beatings tear gas and hard labour will fix

#3 Matrixrail_Louie

Member

Group: Members
Posts: 218
Joined: 30-December 12
Gender:Male
Location:Your mom's house

Posted 31 December 2012 - 11:43 AM

I have a rotor.. I got it for a while.. let me tell you it was terrible... I would be shooting and get a pod to empty into my rotor and at least 10 balls would be sitting on the top! I switched to an exalt and it was much better! go exalt :tup:

2012 Proto Reflex Rail FST- http://www.techpb.co...howtopic=215777

#4 get.lit.up!

200lb of unpredictable coming to hunt ya ;)

Group: Members
Posts: 2,528
Joined: 08-August 11
Gender:Male

Posted 31 December 2012 - 02:47 PM

I've seen exalt and dye speed feeds sag pretty bad. I've seen a virtue crown fingers break.

Personally I would recommend from rotors and other hoppers I've been lent the crown2 and crownsf are the way to go. I haven't seem or used any epics, km spines, or anything like that.

But think this way if you had to buy like 5 km spines that one crownsf can last for you save money on downtime, and time spent on getting it

See my about me for useful things like feedback!

#5 jsg_nado

I'm a bird motha f**ka I'm a bird

Group: Members
Posts: 239
Joined: 24-January 11
Gender:Male
Location:Coronado, CA

Posted 18 January 2013 - 02:44 PM

Matrixrail_Louie, on 31 December 2012 - 11:43 AM, said:

Which spine did you have? Km feeds are the softest feeds on the market. I've never had that problem.

GoGo 13 Proudly Sponsored by PaintballGateway, KM, AlmostFamous, APX, Thump Barrels and Camp Pendleton Paintball
Marq7 For Sale
01010000 01100001 01101001 01101110 01110100 01100010 01100001 01101100 01101100 Not a programmer? Oh. Never mind.

#6 Phoenix01

Member

Group: Members
Posts: 181
Joined: 15-November 12
Gender:Male

Posted 18 January 2013 - 06:27 PM

I had the same predicament back when I was looking at a speed feed for my rotor and to be honest what helped me make my decision was watching some review videos. I ended up going with the exalt, which is actually the cheapest one brand new. I went on the fact that the exalt allowed more paint in and actually did just as good of a job holding paint in as the km spine.

#7 bassfisher

Senior Member

Group: Members
Posts: 1,387
Joined: 16-November 12

Posted 18 January 2013 - 07:31 PM

I don't know about the older spines, but the spine 2.0 is Definately pretty good. It also has a lifetime warranty against sagging, and it holds paint in really well.

Carolina Riot Scenario Team

#8 QuickLime

Member

Group: Members
Posts: 88
Joined: 04-January 13

Posted 18 January 2013 - 11:23 PM

I'm surprised no one has mentioned the HK Epic speed feed. Its a bit expensive but is the best one out on the market IMHO.

Feedback!1/0/0

#9 marceldacs

Junior Member

Group: Members
Posts: 957
Joined: 14-November 12
Gender:Male
Location:Chicago,IL

Posted 18 January 2013 - 11:28 PM

QuickLime, on 18 January 2013 - 11:23 PM, said:

I'm surprised no one has mentioned the HK Epic speed feed. Its a bit expensive but is the best one out on the market IMHO.

this^
A friend of mine has it on his z2 and it works really well. Best out of the bunch i'd say. The only thing that deters people from it is its cost.