[Dynasty Pntballer]

Alright so I am wondering why when I put my new evlution III loader in to my diablo wrath it swirls around a lot. Also why does my tank not seem to fit on my gun because the pressure gauge is getting stuck under the gun when I try and twist the tank in?

[rebel492991]

you need to tighten the feed neck down more, and if you have the feed neck as tight as it goes and the hopper still spins take some electrical tape and rap the feed neck of the hopper a few times to make it bigger and then try it out in the feed neck.

for the tank i would try moving the asa farther back on the grip frame and try it and if that dosnt work you are going to need to bu a new asa.

[BAMitsON]

put a oring around the feedneck and then push it in

[pbgunner93]

screw the feed neck down all the way or tape the hopper feedneck. You could also buy a nice adjustable feed neck.

as for the tank, i would get a drop forward

[paintballfreak36]

put an oring in the feeneck and put you hopper in and for the tank consult a trained pro

[Hazmat Paintball]

just for reference here. what type of tank do you have?

[Dynasty Pntballer]

To move the ASA back on the wrath do use just have to unsrew it and move it?

[goat79]

u don't need to turn the tank all the way tight, just till the gun airs up

[rebel492991]

this will make the tank have a slow recharge rate.

[CoolCarter]

With your Diablo Wrath, the feedneck needs to be tightended down all the way. After that, if the hopper still isn't being held in tight enough you can do one of two things. 1, wrap electrical tape around the feedneck or 2, put an O-ring or two on the feedneck of the eggy. As far as your air tank problems go you should consult a paintball technician. They ought to have another asa that will allow you to fit your airtank on. Also, they can likely offer you different air tanks that would work better with your current marker.


Best of luck!
Carter Davison

[ExcessiveEgo]

goat79, on Oct 2 2008, 02:26 PM, said:

u don't need to turn the tank all the way tight, just till the gun airs up

NOOOO, that is dangerous, makes it much easier for the threads to strip out in the ASA, they are only alluminum....

get a rail mount ASA and a CP (or similar) rail..... it does 2 things, lowers ur tank so it may clear your frame, and allows you to move it to a comfortable position............

and to the above ^^^ drop forwards are bad also, they teach you bad from... they were really only necessary with the old school 120ci tanks

[1q2w3e4r]

you can try taking a bit of sandpaper to the feedneck (take it off the gun) and to the hoppers feedneck it worked for me i went through 4 feednecks and this is the only thing that worked. btw i have the eggy 2

[tweetyarmy]

those loaders feednecks tend to run small

[Lucas]

Its simple. the feednecks are somewhat small. You'll notice that if you put multiple hoppers on a gun, you'll notice that you need to slightly adjsut the tightness

[pb4evr]

feedneck

[Newman513]

Electric Tape on the feedneck.

[Newman513]

Electric Tape on the feedneck.

[Im4EverKing]

1q2w3e4r, on Oct 3 2008, 05:38 PM, said:

you can try taking a bit of sandpaper to the feedneck (take it off the gun) and to the hoppers feedneck it worked for me i went through 4 feednecks and this is the only thing that worked. btw i have the eggy 2

The feedneck is already too small. he doesn't want to make it smaller. But yea just use an o-ring or something. I just use a bit of tape arround the feedneck just to widen it a bit and it works well.