TechPB Forum: Where does your Rotor jam? - TechPB Forum

Jump to content

Page 1 of 1

You cannot start a new topic
You cannot reply to this topic

Where does your Rotor jam?

#1 CarsonRemchuk

Newbie

Group: Members
Posts: 30
Joined: 27-December 11

Posted 26 June 2012 - 05:22 PM

Hey I was doing some drop tests with my Rotor today to see if it would jam and it was jamming a couple time. Of course its a V3, batteries are fine, loader is clean. Mine is jamming in between the wheel and the arm, like the arm is catching on the paintball and pushing it up against the wheel, is this normal for a jam??? And there is no tension when I try to unjam it with the unjamming fin so it won't work.

#2 ShadowZero

Karma Police

Group: Members
Posts: 4,174
Joined: 04-December 09
Gender:Male
Location:In Your Pants

Posted 26 June 2012 - 05:37 PM

That's where it normally jams.

What kind of paint are you putting through it? You need to put good, round paint into it for it feed to its max potential.

-My YouTube (More Videos To Come Soon!)
Set-Up: Marq Rapper, Dye Rotor, Ninja 68/45
Be a Brick Wall, Don't Break Down

#3 crPaliza

Senior Member

Group: Members
Posts: 1,041
Joined: 15-September 11
Gender:Male

Posted 27 June 2012 - 02:10 AM

Lowering your Rotor tension should significantly reduce your jams. Check out the video below.

Feedback +2/0/0

#4 NJC

pumper

Group: Members
Posts: 3,391
Joined: 11-July 11
Gender:Male
Location:Utah

Posted 27 June 2012 - 02:52 AM

my rotor has only jammed once on my gun out of roughly 30 or so cases, but jams during drop tests somewhat regularly. it jams more when it's spins freely at full speed

-ORaNGe-, on 18 November 2011 - 04:24 PM, said:

I split my vote, half for etekgirl's body, half for her mind, because I respect a woman's mind just as much as her cans.
*Waits to get hit*

#5 TK-421

Me So Horny! :D

Group: BST Moderator
Posts: 24,841
Joined: 29-August 09
Gender:Male
Location:Austin, Texas

Posted 27 June 2012 - 02:53 AM

My rotor doesn't jam.

TBC PA DPOC BST Ads 16/0/0

#6 cybermaniac15

Elite Member

Group: Members
Posts: 5,448
Joined: 04-December 10
Gender:Male
Location:Southern-California

Posted 27 June 2012 - 02:54 AM

Both of mine never jam, thought it was this weekend, but it was actually my gun.

Feedback
http://www.techpb.co...1&#entry1905487
PM8 and Extcy: http://www.techpb.co...pic=215216&st=0

#7 LUXOR54

TechPB's smart ass

Group: Members
Posts: 3,164
Joined: 31-July 11
Gender:Male
Location:CANADA EH!

Posted 27 June 2012 - 03:36 PM

i thought mine was jamming alot one day. turns out the board got fried a week out of box...

New found pumper,
Set-up: Black/gold E2 Karnivor, Dye rotor, Guerrilla air 68/4500, CP 14" .685, Black/Gold Dye I4's, Dye core pads, Venomwear, Etek3 LT. Orange 2k5 superstock, CCM'd
Proud Canadian citizen

#8 CarsonRemchuk

Newbie

Group: Members
Posts: 30
Joined: 27-December 11

Posted 28 June 2012 - 06:47 PM

TK-421, on 27 June 2012 - 02:53 AM, said:

My rotor doesn't jam.

Oh your cool lol, jk man.

I was using Graffiti with it but I was just drop testing in it, I haven't used it on a gun yet because mine is at the factory but we will see when it comes back. I did lower the tension and it did jam still. The paint is a little what you might say sticky because I used it at a practice where it was around 100 degrees

#9 Kikkia

Despite the high cost of living, it remains very popular.

Group: Members
Posts: 1,629
Joined: 20-June 10
Gender:Male
Location:Peosta IA

Posted 01 July 2012 - 07:32 PM

My rotor does not jam to much, only with crap paint in crap weather.

Etek3 /Dye Rotor/GI 68/45

#10 HU Soldier

Say Chesse!! your about to get Painted

Group: Members
Posts: 1,422
Joined: 19-June 10
Gender:Male
Location:Coxs Creek Ky, 40013

Posted 03 July 2012 - 03:49 PM

mine jammed when i shot paint that was literally egg shaped

http://www.techpb.com/forum/index.php?showtopic=191749 <-------- 7/0/0 feedback

#11 andrewthewookie

Pull start me and I'm yours ;)

Group: Moderator
Posts: 19,436
Joined: 22-August 09
Gender:Female
Location:Your bedroom

Posted 03 July 2012 - 03:52 PM

I've noticed that in the event of jams, my rotor spins enough through the anti-jam, that the trigger is almost useless. I go to un-jam, and the trigger is loose through its whole travel, meaning I have to actually empty out the paint, and physically dislodge the paint stuck in the arms.

Hybrid SFT • 09 Impulse • HB REV-i • Macroless Mech Ion
Rotor • Grillz • PE 70/45 • Feedback - 21/0/0
Fear is the mind-killer

#12 m4ndark

Heart is what wins tournaments - Fraige

Group: Members
Posts: 1,287
Joined: 25-December 10
Gender:Male
Location:Brazil

Posted 04 July 2012 - 12:29 PM

seriously ive never had a rotor jam, using shitty paintballs, tournament grade paintballs, playing on semi, psp ramp, you call it. ive never had one single jam with it. for me it is the best hopper ever.

Gewn Owners * Rotor Syndicate * HK Army Collective
Brazil- passionate baller