[ninjapaintball]

Thanks but they were made for the sponsored teams and we are out of them. Keep checking back as we are thinking about getting more?

[gogpaintballer]

I have a ninja fill whip on a shoebox compressor and I need another female end where can I buy one?

[ninjapaintball]

We don't recommend the fill whip on the shoe box. The whip was designed to fill and empty, not fill for 4 hours. Contact the shoebox guys and they should be able to help

[gogpaintballer]

Why isnt it reccomended?

[ninjapaintball]

The whip was designed to fill and then release the pressure, not hold it for hours while filling

[gogpaintballer]

Can I still use it?

[ninjapaintball]

We do not recommend it

[gogpaintballer]

Where can I order some orings for my tank?

[ninjapaintball]

Check your local Proshop first. Then check out the great Internet stores. Sorry but we do not sell direct from our website anymore, this helps to support our dealers

[gogpaintballer]

My Ninja 68/4500 is leaking air when I screw it into my PMR and will also leak when I turn the ASA ON, on my Extcy. Whats wrong?

This post has been edited by gogpaintballer: 07 June 2012 - 07:01 PM

[ninjapaintball]

It sounds like it only leaks when in an Asa which coul dbe the orings at the top of the reg. lube or replace those orings and this should help

This post has been edited by ninjapaintball: 07 June 2012 - 07:26 PM

[gogpaintballer]

What kind of lube should I use?

[ninjapaintball]

Anything u use on your gun

[gogpaintballer]

I just shot my Pmr with my ninja 68/4500 and when I ran out of air I continued to walk the trigger, to make sure all the air was out and after the gauge read 0 psi for a couple seconds and then air started to burst out of a hole below the reg. What happened and is it permanant?

[ninjapaintball]

What hole? So you menthe 2 set screws in the bonnet? If that is the case then it is not a concern, there was not enough pressure to seal the orings on the piston.

This post has been edited by ninjapaintball: 26 June 2012 - 07:31 PM

[gogpaintballer]

ninjapaintball, on 26 June 2012 - 07:30 PM, said:

What hole? So you menthe 2 set screws in the bonnet? If that is the case then it is not a concern, there was not enough pressure to seal the orings on the piston.

Not exactly a hole but it looked like something you could turn with a allen key on thr bottle.

[ninjapaintball]

It sounds like the piston orings and refill the system, you should not have a problem because you were so low of pressure last time.

[Box]

Hey Ray (I'm assuming it's Ray, forgive me if I'm incorrect), any chance you have spare set screws for Pro Regs? I bought one at PSP Chicago in late June and literally the next weekend I ended up losing two screws on the rotating ring.

[ninjapaintball]

Box, on 09 July 2012 - 09:20 PM, said:

Hey Ray (I'm assuming it's Ray, forgive me if I'm incorrect), any chance you have spare set screws for Pro Regs? I bought one at PSP Chicago in late June and literally the next weekend I ended up losing two screws on the rotating ring.

check your local store first, if not then let me know and i can get some out to you or see you at the next event?

[Box]

ninjapaintball, on 10 July 2012 - 09:15 AM, said:

Box, on 09 July 2012 - 09:20 PM, said:

Hey Ray (I'm assuming it's Ray, forgive me if I'm incorrect), any chance you have spare set screws for Pro Regs? I bought one at PSP Chicago in late June and literally the next weekend I ended up losing two screws on the rotating ring.

check your local store first, if not then let me know and i can get some out to you or see you at the next event?

Been a while since I remembered about this post! sorry for not following up

My local field in Pekin doesn't have any spare screws and my team isn't attending MAO any longer. Should I PM you with some contact info?