TechPB recommended Marq & Intimidator Settings
Posted 28 October 2008 - 07:04 PM
Posted 13 January 2009 - 01:26 AM
Bob Long Vice-Black (laser 4c eyes,USB OLED Yakuza Board, Kila Dirty Bolt,
Kila magnet detents, Gear Drive on/off ASA, Low Pressure Poppet)
Pinokio Hopper with Virtue Speed Feed(ultra soft)
Crossfire 68/4500 carbon fiber
Posted 18 January 2009 - 08:59 PM
Images used in signatures are to be less than Width of 600px, and height of 160px. Only ONE image is allowed in the signature, and it must be 30k or less. Only 5 lines of text are allowed. No text larger then size 2 is allowed in the signature.
Posted 01 February 2009 - 01:59 AM
You can't reliably set your LPR without an LPR gauge. Depending on your marker you could find out what the typical stock setting is from the flush position of the adjustment screw on the LPR. For the Vice and Protege's LPR it's about 1 1/2 turns in from flush. From there you fine tune and adjust with the LPR tester.
If your LPR is way off it can throw off the HPR, and vice versa.
<!--sizeo:2--><span style="font-size:10pt;line-height:100%"><!--/sizeo--><a href="http://www.SoCalGhosts.com" target="_blank">www.SoCalGhosts.com</a> - Proudly Sponsored by: ANS Gear <a href="http://www.ANSGEAR.com" target="_blank">www.ANSGEAR.com</a> and Save Phace <a href="http://www.SAVEPHACE.com" target="_blank">www.SAVEPHACE.com</a><!--sizec--></span><!--/sizec-->
<!--sizeo:2--><span style="font-size:10pt;line-height:100%"><!--/sizeo-->Mike Phillips: "Pound for pound - Bob Long Vice, one of the best guns on the market...ever! This gun is absolutely absurd."<!--sizec--></span><!--/sizec-->
Posted 11 March 2009 - 06:55 PM
<a href="http://www.techpb.com/forum/index.php?showtopic=39853" target="_blank"><!--sizeo:2--><span style="font-size:10pt;line-height:100%"><!--/sizeo--><!--coloro:#ff0000--><span style="color:#ff0000"><!--/coloro--><!--fonto:Comic Sans MS--><span style="font-family:Comic Sans MS"><!--/fonto-->Proud owner of an Russian Legion Timmy. <!--fontc--></span><!--/fontc--><!--colorc--></span><!--/colorc--><!--sizec--></span><!--/sizec--></a> <!--sizeo:1--><span style="font-size:8pt;line-height:100%"><!--/sizeo--><!--coloro:#006400--><span style="color:#006400"><!--/coloro--><!--fonto:Comic Sans MS--><span style="font-family:Comic Sans MS"><!--/fonto-->Fat Ballers club<!--fontc--></span><!--/fontc--><!--colorc--></span><!--/colorc--> <!--sizec--></span><!--/sizec-->
Posted 12 March 2009 - 12:28 AM
your dwell is at 4ms...raise it to 8
the "1" is actually another "L"...since dwell is spelled with 2 L's and not one...
edit: btw Mike, you dont but dow55 on everything. you use triflow(or some paintball oil) on the bolt orings. putting dow on the delrin bolt will cause it to swell and drag. therefor leading other major problems.
This post has been edited by gamer565: 12 March 2009 - 12:31 AM
Posted 02 April 2009 - 08:46 PM
zop1o's marq and auto cocker tuning and repair services
Posted 06 April 2009 - 11:43 AM
NO NO NO DUDE! your LPR pressure doesn't need to be change when you get the LP valve since its longer it will need the same amount of pressure for the ram travel with out any problem
I have mine on 65 PSI for both type of valve
175 PSI on the HPR with LP valve
215 PSI with HP valve
8 dwell same for both
thin coat of dow 55 and ram the ram must be grease free on both ends, you will need to relub it more times than a thick coat but you wont get first drop off shoot
Please use triflow on the bolt 2-3 drops and make a thin even coat
Why Triflow? Firs it has Teflon and will make your bolt enclosure last more. Second Triflow repels dust and wont end up on your marker eyes
Posted 26 April 2009 - 09:39 PM
Posted 13 June 2009 - 10:58 PM
dwell 9ms(value 10 on virtue)
eye delay 3ms
anti bolt stick off(no fsdo)
hpr at 155psi 290-300fps
efficiency with 45/45: half a case from 3,000psi with about 200psi left after test. paint used for test: anarchy with dye boomstick 689
Oddly enough my ashcroft 0-300psi gauge read 155psi on my torpedo regulator when I set my alias to shoot at 300fps with all stock parts and settings. I dont have a volumizer or a light poppet spring, its all alias stock internals. IDC about getting the lowest settings on my hpr so I have no reason to make up 155psi in case anyone thought twice about that claim.