TechPB Forum: Pumpmag Build - TechPB Forum

Jump to content

Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Pumpmag Build I am determined to finish a build!

#1 User is offline   WiscoBaller 

  • Master Member
  • PipPipPipPipPipPip
  • Group: TechPB Players Club
  • Posts: 2,655
  • Joined: 11-August 10
  • Gender:Male

Posted 17 December 2012 - 06:59 PM

Hey TechPB.

Putting this up a little late, because after my last two builds I put up here I did not finish, I did not want to get the sell bug before I finished this. I do not have all parts in my posession right now, as some are still filtering in and some are being worked on.

I am building a pumpmag.

For those unaware, a pumpmag operates simmilar to an automag, except there is an additional spring between the bolt and the valve, causing it to not reset fully. The pump rod then presses the bolt over the sear, allowing it to fully reset.

Here are my parts so far.

ULE Body Milled (With Luke)
Minimag Valve
AM/MM rail/sear/axle
Benchmark single trigger frame
Shocktech On/Off ASA and rail.
AM/MM Vertical ASA
Bob Long Clamping feedneck
Dye Xcel barrel
XM15 Pump Kit

What I have in my possession right now:
Posted Image

Have:
Minimag valve
Rail/Sear/Axle
Frame
ASA
Vert ASA
Barrel

In mail:
XM15 Pump Kit
Feedneck

Need:
four macro fittings
1'6" macro

To do:
Send rail to Luke to mill.

This post has been edited by WiscoBaller: 17 December 2012 - 07:01 PM

University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST

#2 User is offline   tallsmallboy44 

  • Space Cowboy
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 3,499
  • Joined: 17-August 10
  • Gender:Male
  • Location:Ohio

Posted 17 December 2012 - 08:14 PM

Looks good. Hope you actually finish this one. ;)

View Post5ozofpain, on 18 September 2012 - 05:59 PM, said:

fuck yolo
#carpediem
Feedback 2/0/0

#3 User is offline   WiscoBaller 

  • Master Member
  • PipPipPipPipPipPip
  • Group: TechPB Players Club
  • Posts: 2,655
  • Joined: 11-August 10
  • Gender:Male

Posted 19 December 2012 - 01:16 PM

got the feedneck, rail is shipped out, and pump kit is on the way.
University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST

#4 User is offline   tallsmallboy44 

  • Space Cowboy
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 3,499
  • Joined: 17-August 10
  • Gender:Male
  • Location:Ohio

Posted 02 January 2013 - 08:10 PM

Any progress on this?

View Post5ozofpain, on 18 September 2012 - 05:59 PM, said:

fuck yolo
#carpediem
Feedback 2/0/0

#5 User is offline   WiscoBaller 

  • Master Member
  • PipPipPipPipPipPip
  • Group: TechPB Players Club
  • Posts: 2,655
  • Joined: 11-August 10
  • Gender:Male

Posted 02 January 2013 - 09:00 PM

got the pumpkit, the rail and body are still with luke, the feedneck is still here.
University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST

#6 User is offline   get.lit.up! 

  • 200lb of unpredictable coming to hunt ya ;)
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 2,521
  • Joined: 08-August 11
  • Gender:Male

Posted 02 January 2013 - 09:15 PM

Price of build?
Posted Image
See my about me for useful things like feedback!

#7 User is offline   WiscoBaller 

  • Master Member
  • PipPipPipPipPipPip
  • Group: TechPB Players Club
  • Posts: 2,655
  • Joined: 11-August 10
  • Gender:Male

Posted 02 January 2013 - 10:54 PM

Have:
Body-$80
Minimag valve-$30
Rail/Sear/Axle-$20
Frame-$30
ASA-$12
Vert ASA-Free with rail
Barrel-$8

In mail:
XM15 Pump Kit-$60
Feedneck-$8

Need:
four macro fittings-$12
1'6" macro-$1.50

Milling-$60

Total-$320

A bit expensive, but Luke does good work (Rainman would do milling for $40) and I didn't want to use a CF frame, like the metal benchmark better. Pumpmags can be picked up like how I built for around the $300 mark, but this is one I plan on holding onto.
University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST

#8 User is offline   WiscoBaller 

  • Master Member
  • PipPipPipPipPipPip
  • Group: TechPB Players Club
  • Posts: 2,655
  • Joined: 11-August 10
  • Gender:Male

Posted 03 January 2013 - 11:56 PM

rail and body shipped back yesterday, should be here by the weekend.
University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST

#9 User is offline   WiscoBaller 

  • Master Member
  • PipPipPipPipPipPip
  • Group: TechPB Players Club
  • Posts: 2,655
  • Joined: 11-August 10
  • Gender:Male

Posted 05 January 2013 - 11:21 PM

Posted Image

It is done, but I am hitting a few snags. I do not have a HP tank currently, so I am looking to buy a HP reg to throw on a tank, and the pump arm is binding on the body. Gonna have to do a bit of tinkering on it, but so far I like it.
University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST

#10 User is offline   tallsmallboy44 

  • Space Cowboy
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 3,499
  • Joined: 17-August 10
  • Gender:Male
  • Location:Ohio

Posted 06 January 2013 - 11:25 AM

Looks nice.

View Post5ozofpain, on 18 September 2012 - 05:59 PM, said:

fuck yolo
#carpediem
Feedback 2/0/0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users