Jump to content


Photo

Why is my EVLUTION III loader very loose when I put it in my new Diablo Wrath?


  • Please log in to reply
17 replies to this topic

#1 Dynasty Pntballer

Dynasty Pntballer

    Newbie

  • Members
  • Pip
  • 38 posts

Posted 30 September 2008 - 10:25 AM

Alright so I am wondering why when I put my new evlution III loader in to my diablo wrath it swirls around a lot. Also why does my tank not seem to fit on my gun because the pressure gauge is getting stuck under the gun when I try and twist the tank in?

#2 rebel492991

rebel492991

    Sophomore Member

  • Members
  • PipPipPip
  • 747 posts
  • Gender:Male
  • Location:Plantcity Florida

Posted 30 September 2008 - 11:47 AM

you need to tighten the feed neck down more, and if you have the feed neck as tight as it goes and the hopper still spins take some electrical tape and rap the feed neck of the hopper a few times to make it bigger and then try it out in the feed neck.

for the tank i would try moving the asa farther back on the grip frame and try it and if that dosnt work you are going to need to bu a new asa.

#3 BAMitsON

BAMitsON

    BROKE member

  • Members
  • PipPip
  • 151 posts
  • Gender:Male
  • Location:Boston, MA

Posted 30 September 2008 - 12:17 PM

put a oring around the feedneck and then push it in
<!--coloro:#708090--><span style="color:#708090"><!--/coloro--><!--coloro:#708090--><span style="color:#708090"><!--/coloro--><div align='center'><!--coloro:#696969--><span style="color:#696969"><!--/coloro--><strike>$$</strike> <!--colorc--></span><!--/colorc--><a href="http://www.techpb.co...7&#entry106707" target="_blank"><!--coloro:#696969--><span style="color:#696969"><!--/coloro-->BROKE TechPB Players Club<!--colorc--></span><!--/colorc--></a><!--coloro:#696969--><span style="color:#696969"><!--/coloro--> <strike>$$</strike><!--colorc--></span><!--/colorc--></div><div align='center'><!--coloro:#696969--><span style="color:#696969"><!--/coloro-->.: BAMitsON :. .: ciolfi0118 :. .: ItalianGigalo :.
<!--colorc--></span><!--/colorc--></div><!--colorc--></span><!--/colorc--><!--colorc--></span><!--/colorc-->

#4 pbgunner93

pbgunner93

    Member

  • Members
  • PipPip
  • 87 posts

Posted 30 September 2008 - 07:48 PM

screw the feed neck down all the way or tape the hopper feedneck. You could also buy a nice adjustable feed neck.

as for the tank, i would get a drop forward
Team "Nuclear Dinosauer Commandos"
Thanks for helping us get a team name, pm me if you wish to join this team
LilBill78: "do all electric hopper use batterys?"

#5 paintballfreak36

paintballfreak36

    Member

  • Members
  • PipPip
  • 122 posts
  • Gender:Male
  • Location:Oregon

Posted 30 September 2008 - 11:47 PM

put an oring in the feeneck and put you hopper in and for the tank consult a trained pro

#6 Hazmat Paintball

Hazmat Paintball

    Sophomore Member

  • Members
  • PipPipPip
  • 542 posts
  • Gender:Male
  • Location:Phoenix Arizona

Posted 30 September 2008 - 11:56 PM

just for reference here. what type of tank do you have?
My sig was edited / removed because it was not within the rules. Images used in signatures are to be less then Width of 600px, and height of 160px. Only ONE image is aloud in the signature, and it must be 30k or less. Only 5 lines of text are aloud. No text larger then size 2 is aloud in the signature.

My image was over the 30k AND My text was too big I really am a muppet

#7 Dynasty Pntballer

Dynasty Pntballer

    Newbie

  • Members
  • Pip
  • 38 posts

Posted 01 October 2008 - 05:32 PM

To move the ASA back on the wrath do use just have to unsrew it and move it?

#8 goat79

goat79

    Newbie

  • Members
  • Pip
  • 43 posts
  • Gender:Male
  • Location:Alberta, Canada

Posted 02 October 2008 - 01:26 PM

u don't need to turn the tank all the way tight, just till the gun airs up

#9 rebel492991

rebel492991

    Sophomore Member

  • Members
  • PipPipPip
  • 747 posts
  • Gender:Male
  • Location:Plantcity Florida

Posted 02 October 2008 - 01:29 PM

this will make the tank have a slow recharge rate.

#10 CoolCarter

CoolCarter

    Muppet Squad

  • Members
  • PipPipPip
  • 445 posts
  • Gender:Male
  • Location:Massiiiicheeewwwsitts

Posted 02 October 2008 - 02:44 PM

With your Diablo Wrath, the feedneck needs to be tightended down all the way. After that, if the hopper still isn't being held in tight enough you can do one of two things. 1, wrap electrical tape around the feedneck or 2, put an O-ring or two on the feedneck of the eggy. As far as your air tank problems go you should consult a paintball technician. They ought to have another asa that will allow you to fit your airtank on. Also, they can likely offer you different air tanks that would work better with your current marker.


Best of luck!
Carter Davison
Fox4paintball.com
BRAWL BRAWL BRAWL BRAWL
Smoke Bears.
WE KILL SUCKERS

#11 ExcessiveEgo

ExcessiveEgo

    Sophomore Member

  • Members
  • PipPipPip
  • 395 posts
  • Gender:Male
  • Location:NewHampshire

Posted 02 October 2008 - 06:02 PM

u don't need to turn the tank all the way tight, just till the gun airs up


NOOOO, that is dangerous, makes it much easier for the threads to strip out in the ASA, they are only alluminum....

get a rail mount ASA and a CP (or similar) rail..... it does 2 things, lowers ur tank so it may clear your frame, and allows you to move it to a comfortable position............

and to the above ^^^ drop forwards are bad also, they teach you bad from... they were really only necessary with the old school 120ci tanks
Competition doesn't kill companies........Smartparts does........AKA for life

My Collection - My Collection Updated



#12 1q2w3e4r

1q2w3e4r

    Newbie

  • Members
  • Pip
  • 9 posts

Posted 03 October 2008 - 07:38 PM

you can try taking a bit of sandpaper to the feedneck (take it off the gun) and to the hoppers feedneck it worked for me i went through 4 feednecks and this is the only thing that worked. btw i have the eggy 2

#13 tweetyarmy

tweetyarmy

    UKS

  • Members
  • PipPipPipPipPip
  • 2,206 posts
  • Gender:Male
  • Location:918

Posted 03 October 2008 - 08:04 PM

those loaders feednecks tend to run small

Jolly Green splatterpb podiumpaintball
fat front player/agg/elite gun owner
Members Of The Owl Council
TWEETY

#14 Lucas

Lucas

    Elite Member

  • Retired Staff
  • PipPipPipPipPipPipPip
  • 5,342 posts
  • Gender:Male
  • Location:Virginia, USA

Posted 03 October 2008 - 08:06 PM

Its simple. the feednecks are somewhat small. You'll notice that if you put multiple hoppers on a gun, you'll notice that you need to slightly adjsut the tightness

#15 pb4evr

pb4evr

    Member

  • Members
  • PipPip
  • 124 posts
  • Gender:Male
  • Location:california

Posted 04 October 2008 - 09:28 PM

feedneck
Rusty Glaze fan #1 GLENN TAKEMOTO FAN #2 Gno Benedicto FAN #2 Brian "LB"Fow FAN #2
LA Infamous Fan #3

#16 Newman513

Newman513

    PaintballJesus

  • Members
  • PipPipPipPipPipPip
  • 2,924 posts
  • Gender:Male

Posted 05 October 2008 - 07:02 AM

Electric Tape on the feedneck.

Posted Image


"Only in the Pump Forum"

#17 Newman513

Newman513

    PaintballJesus

  • Members
  • PipPipPipPipPipPip
  • 2,924 posts
  • Gender:Male

Posted 05 October 2008 - 07:02 AM

Electric Tape on the feedneck.

Posted Image


"Only in the Pump Forum"

#18 Im4EverKing

Im4EverKing

    Member

  • Members
  • PipPip
  • 246 posts
  • Gender:Male
  • Location:Cali

Posted 05 October 2008 - 01:13 PM

you can try taking a bit of sandpaper to the feedneck (take it off the gun) and to the hoppers feedneck it worked for me i went through 4 feednecks and this is the only thing that worked. btw i have the eggy 2



The feedneck is already too small. he doesn't want to make it smaller. But yea just use an o-ring or something. I just use a bit of tape arround the feedneck just to widen it a bit and it works well.
>> Anyone who's got a White Flex for sale hit me up <<

My image was over the 30k, im so naughty.




2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users