Jump to content


Photo

Dye marker Manuals!


  • Please log in to reply
1 reply to this topic

#1 Rlpaintball

Rlpaintball

    Newbie

  • Members
  • Pip
  • 40 posts

Posted 30 September 2008 - 08:27 PM

Posted Image
DM4 Manual:

Posted Image
DM5/C Manual:

Posted Image
DM6 Manual:

NOTE: 5 turns out on LPR in manual is incorrect.
75 psi is the stock LPR setting. On the DM6... 75 psi is around 3 turns out. 5 turns out on this LPR turned to be 100 psi when looking at a gauge:

NOTE: DM6 LPR outer o-ring typo
The 3 outer o-rings on the LPR are listed as 012 BN70 in the DM6 manual. This is an incorrect o-ring size. The correct sized o-ring for the 3 outer o-rings on the DM6 LPR are 013 BN70.

Posted Image
DM7 Manual: download

Posted Image
DM8 Manual: download
NOTE: There is a typo in the DM8 manual. The LPR should be 2.5 to 3 turns out for 75psi. NOT 5 turns out.



#2 Rlpaintball

Rlpaintball

    Newbie

  • Members
  • Pip
  • 40 posts

Posted 30 September 2008 - 08:44 PM

TEXT Version: UL Board Colors and Programming



Blue - Boot Sequence
Red - Breech is clear, no ball (eye on)
Green - Ball in breech, ready to fire (eye on)
Blinking Red - Eye is off
Blinking Green - Eye failure (see DM6 Board, page 5)
Blinking Blue - Indicates a low battery, battery should be changed as soon as possible





Configuration Mode

The following settings can only be modified in configuration mode. To activate the configuration mode, turn your marker off and set DIP switch 2 to the ON position. Next, turn your marker on.
The LED's cycle through all colors for one second to indicate that you have entered the configuration mode. To cycle through different settings, pull and release the trigger. Configuration mode has 4 settings that can be changed.





Green - Trigger Sensitivity

Values 1 - 20 (factory default 5)
Trigger sensitivity is the amount of time that the trigger has to be released before the next trigger pull is allowed. In some situations with too low of a value, the DM6 can register more trigger pulls than what was actually pulled. This can cause the DM6 to shoot full auto, even in semi-automatic mode. To fix this, set trigger sensitivity setting higher.




Red - Dwell

Values 1 - 30 (factory default 18)
Dwell is the amount of time that the solenoid will be activated. Follow these steps for the best way to set your dwell:
Remove loader and any paintballs from the DM6 marker.
With the dwell set at 10, start increasing the value until the marker begins to fire.
When you reach the setting where the marker begins to fire, get some paint and a loader and go to a chronograph.
Increase the dwell until you see no increase in the velocity. This is the optimal dwell setting to be used.




Blue - Rate Of Fire (ROF)
[When Anti Chop Eye (ACE) is deactivated]

Values 1 - 20 (factory default 20bps)
The ROF setting is used to set the maximum rate of fire of the DM6. The values do not correspond directly to a certain
Balls Per Second (BPS) value. You will need to use the table below to locate your desired maximum ROF setting.
The factory setting is 20 (30bps).




Value = BPS

1 10 11 15.6
2 11 12 15.9
3 12 13 16
4 13 14 18
5 14 15 20
6 14.5 16 22
7 14.7 17 24
8 14.9 18 26
9 15.2 19 28
10 15.4 20 30




Yellow - Firing Mode

Values 1 - 3 (default 1)
This setting changes the Firing mode of the DM6. Default is semiautomatic. In the semiautomatic mode, one trigger pull shoots out one paintball. The PSP/NPPL mode and The Millennium mode follow the rules of the
paintball tournaments series.
Value 1 - NPPL/Semi automatic Mode
Value 2 - PSP Mode
Value 3 - Millennium Mode

NOTE: You cannot turn your marker off with the power button when the marker is in configuration mode. You must first set DIP switch 2 to the off position.


TO CHANGE THE VALUE OF A SETTING:
  • While in configuration mode, pull the trigger and hold it for more than one second. The LED will flash to
    indicate the previous setting. After that, you can set the new value with the trigger. For example, if you want
    to change the trigger sensitivity to 7 units:
  • Cycle through menus by pulling and releasing the trigger until the LED lights GREEN (trigger sensitivity).
  • Pull and hold the trigger until the LED starts to flash (factory default for trigger sensitivity setting is 5 units,
    so the LED will flash 5 times).
  • When the LED stops flashing, pull and release the trigger seven times in a fast pace. The new value is set
    after you haven't touched the trigger for one second. The LED will cycle through all colors to indicate that
    the new value is saved. All other configurations are changed the same way. Just as in part 2 above, change
    the mode to RED for "dwell" or BLUE for "ROF" to change the desired configurations.
  • To exit configuration mode, set DIP 2 to the off position.
EXAMPLE ON PROGRAMMING FIRING MODES ON STOCK UL BOARD:
  • To activate the configuration mode, turn your marker off and set DIP switch 2 to the ON position. Next, turn your marker on.
    The LED's cycle through all colors for one second to indicate that you have entered the configuration mode.
  • While in configuration mode, click the trigger rapily till you get to Yellow (firing mode).
  • When you get to Yellow, Pull the trigger and hold it for more than one second. The LED will flash to indicate the previous setting. After that, you can set the new value with the trigger. Example: click the trigger 2 times to set it to PSP mode.
    • Value 1 - NPPL/Semi automatic Mode
    • Value 2 - PSP Mode
    • Value 3 - Millennium Mode
  • The LED will cycle through all colors to indicate that the new value is saved.
  • To exit configuration mode, set DIP 2 to the off position.







1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users