Jump to content


Photo

DP G4 won't shoot


  • Please log in to reply
15 replies to this topic

#1 wolverine_05_

wolverine_05_

    Member

  • Members
  • PipPip
  • 60 posts
  • Gender:Male
  • Location:Louisa, KY (Eastern Kentucky)

Posted 22 March 2012 - 06:13 PM

Like stated in title, It just won't shoot. When i air it up, it pushes the bolt back but it won't shoot. When I pull the trigger it won't click or anything, and it wont shoot with eyes off either. So what should I do? Any advice would be helpful.

#2 The Bacon Man

The Bacon Man

    Newbie

  • Members
  • PipPipPipPipPipPip
  • 4,201 posts
  • Gender:Male

Posted 22 March 2012 - 06:25 PM

Broken noid?

#3 abooth2

abooth2

    Sophomore Member

  • Members
  • PipPipPip
  • 409 posts
  • Gender:Male

Posted 22 March 2012 - 06:31 PM

Take out your bolt and lube it up lightly and clean off the back cap and lube it lightly.

#4 mjblount

mjblount

    Senior Member

  • Members
  • PipPipPipPipPip
  • 1,304 posts
  • Gender:Male
  • Location:Rogersville, TN

Posted 22 March 2012 - 06:31 PM

Go to pbnation and ask the question in the dp forum. You will get your answer quickly there. If it is the noid and your under warranty call dp and get a free 1.
Guns I've owned:(in order) Ego 6, PM8, Etek 3lt, Ego 10, Dangerous Power FX
My favorite ones: Ego 6, Ego 10, Dp FX

#5 wolverine_05_

wolverine_05_

    Member

  • Members
  • PipPip
  • 60 posts
  • Gender:Male
  • Location:Louisa, KY (Eastern Kentucky)

Posted 22 March 2012 - 06:45 PM

Can i get a link to the DP section then?

#6 Hitman2513

Hitman2513

    Save a Rock Throw a Mini

  • Members
  • PipPipPipPipPipPipPip
  • 5,741 posts
  • Gender:Male
  • Location:LA Cali


Posted 22 March 2012 - 06:53 PM

Go to pbnation and ask the question in the dp forum. You will get your answer quickly there.

This guy :dodgy:

If you can't feel the click remove the grip frame and make sure the microswitch is free
Posted Image
Bitches love my Spyder Ion

[-ORaNGe-] Trolling isn't an action, it's a lifestyle :)

#7 Klub

Klub

    i haz a pickle

  • TechPB Players Club
  • PipPipPipPipPipPip
  • 4,877 posts
  • Gender:Male
  • Location:alaska


Posted 22 March 2012 - 06:59 PM

Make sure you have a fresh battery in there and that your trigger isnt already activated the microswitch.

#8 808maui

808maui

    Sophomore Member

  • Members
  • PipPipPip
  • 410 posts
  • Gender:Male
  • Location:Maui, Hawaii

Posted 22 March 2012 - 07:17 PM

Make sure you have a fresh battery in there and that your trigger isnt already activated the microswitch.


This. Make sure there is a fresh battery in there.

KAMEHAMEHA

Bob Long Vice

Dangerous Power G3
808 State


#9 recklessbob

recklessbob

    Welts Don't Wipe

  • Members
  • PipPipPipPip
  • 807 posts
  • Gender:Male

Posted 22 March 2012 - 07:25 PM

clean off your bolt and lightly lube it


sounds like wayne brady is gonna have to choke a bitch.

Feedback: http://www.techpb.co...1
AXE F/S/T: http://www.techpb.co...howtopic=217311
68/4500-
http://www.techpb.co...howtopic=215637

#10 CanadianConnection

CanadianConnection

    Member

  • Members
  • PipPip
  • 95 posts

Posted 22 March 2012 - 08:23 PM

your dwell setting might be too low or high also try using it at stock settings of 12 milliseconds

#11 pb=life

pb=life

    I like penguins

  • TechPB Players Club
  • PipPipPipPipPipPipPipPip
  • 8,135 posts
  • Gender:Male
  • Location:nor cal

Posted 22 March 2012 - 09:00 PM

new battery, re-lube the bolt, restore to factory settings. If that doesn't fix it let us know

#12 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 22,147 posts
  • Gender:Female
  • Location:Your bedroom


Posted 22 March 2012 - 09:26 PM

Make sure the solenoid wires are firmly connected to the board, and just to be sure, make sure the battery is good.

RebelSignaturejedicode-1.jpg
Hybrid SFT • 09 Impulse • HB REV-i • Macroless Mech Ion
Rotor • Grillz • PE 70/45 Feedback - 23/0/0


#13 gibbeepbroxzor

gibbeepbroxzor

    Senior Member

  • Members
  • PipPipPipPipPip
  • 1,347 posts
  • Gender:Male

Posted 22 March 2012 - 09:31 PM

Nother thing to check, make sure you don't have the frame tightened down on a wire or anything.

#14 zchrit23

zchrit23

    Junior Member

  • Members
  • PipPipPipPip
  • 752 posts

Posted 23 March 2012 - 04:34 AM

had this problem on my g3, it's possible air got "stuck" on one side of the noid. Don't really remember how i fixed it, but it had something to do with changing my reg flow. I ended up actually taking the reg completely apart at one point after checking all of the above mentioned electrical problems. Oh, another thing, is there rushing air at all?

#15 wolverine_05_

wolverine_05_

    Member

  • Members
  • PipPip
  • 60 posts
  • Gender:Male
  • Location:Louisa, KY (Eastern Kentucky)

Posted 23 March 2012 - 04:57 PM

As soon as I go to the store I will get a new pack of 9v batteries and try that, but i've only shot it once before this so i haven't messed with any of the settings. All of it is how it came in the box, except I've lubbed the bolt. But i'll check everything and i'll refer back to here if anything else occurs.

#16 Jordii

Jordii

    Boats N' Hoes

  • Members
  • PipPipPipPip
  • 777 posts
  • Gender:Male
  • Location:Toronto, ON

Posted 23 March 2012 - 05:23 PM

The G4 is very easy to troubleshoot.

Obviously make sure that the gun is gassed up (regulator is flipped). Then, ensure that there's a sufficient enough amount of air flowing through the reg to cycle the bolt.

What did you re-lube with? Any thick greases will cause the G4's bolt to stick, even consider using oil for the first case or 2.

I'm assuming the LED lights up, so you should have battery. Did you adjust your trigger? If the pull is too short, it could be holding down the microswitch already.

Hope that helps.
Posted Image
If you're under 18 and pay for your gear, put this in your sig.




2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users