Jump to content


Photo

V1 victory


  • Please log in to reply
14 replies to this topic

#1 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 22 July 2012 - 02:20 PM

I can't get the fps over 210. I reset the board. Cleaned and checked all of the orings in the engine and the hpr. Pressure tested it. Upped the dwell to 8. And 210 is where it is.

#2 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 22,001 posts
  • Gender:Female
  • Location:Your bedroom


Posted 22 July 2012 - 04:53 PM

New battery?

And what pressures did you set it at?

RebelSignaturejedicode-1.jpg
Hybrid SFT 09 Impulse HB REV-i Macroless Mech Ion
Rotor Grillz PE 70/45 Feedback - 23/0/0

Closer & Angel A1 F/S/T


#3 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 22 July 2012 - 04:54 PM

I've tried two batteries. I started at 80psi and 210. Tried working my way up but no luck. I have absolutely no leaks. I haven't disassembled the lpr should i?

#4 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 22,001 posts
  • Gender:Female
  • Location:Your bedroom


Posted 22 July 2012 - 05:00 PM

Yeah, a reg service might be in order.

RebelSignaturejedicode-1.jpg
Hybrid SFT 09 Impulse HB REV-i Macroless Mech Ion
Rotor Grillz PE 70/45 Feedback - 23/0/0

Closer & Angel A1 F/S/T


#5 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 22 July 2012 - 05:35 PM

Serviced the lpr and put it back together huge internal leak. Posted Image So I'm disassembling again.

#6 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 22 July 2012 - 05:42 PM

Ok fixed that. The board keeps going on on its own too? But that didnt fix it still 210.

Edited by SamBo, 22 July 2012 - 05:42 PM.


#7 TheGuy

TheGuy

    I like lamp

  • Members
  • PipPipPipPipPipPipPipPip
  • 13,792 posts
  • Gender:Male
  • Location:Cleveland, OH

Posted 23 July 2012 - 01:54 PM

Did you service the HPR also?
Feedback 7/0/0

Rest In Peace

Danijel "Borg" Jagodic


#8 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 23 July 2012 - 04:08 PM

Yes I serviced everything that could be serviced. I'm going to call bob long.

#9 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 23 July 2012 - 06:14 PM

Could be solonoid Posted Image

#10 metsfan521

metsfan521

    Senior Member

  • Members
  • PipPipPipPipPip
  • 2,341 posts
  • Gender:Male
  • Location:Brooklyn, NY U.S.A Earth

Posted 23 July 2012 - 07:35 PM

you should replace ALL of the engine orings



#11 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 23 July 2012 - 07:50 PM

I did

#12 zop1o

zop1o

    megasuperawesomelazerbeamrailgun ofepicdoomandstuff

  • Members
  • PipPipPipPipPipPip
  • 3,585 posts
  • Gender:Male
  • Location:The snake

Posted 14 August 2012 - 12:44 PM

Could be your bore/paint match, I'm having the same problem with my marq and a 691

Edited by zop1o, 14 August 2012 - 12:44 PM.

Marq's men founder. flex owner. I AM A MUPPET! C.O.C. member 91. pump/stock players president. Karnivor Owner councilman. Old School Owner. GUN WHORE.
Posted Image
zop1o's marq and auto cocker tuning and repair services
zop1o's feedback2/0/0

#13 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 14 August 2012 - 03:28 PM

Could be your bore/paint match, I'm having the same problem with my marq and a 691


Well I was using a 685 g6r barrel.

#14 tripp

tripp

    Proudly Sponsored by ANSGear

  • Members
  • PipPipPipPipPip
  • 1,373 posts
  • Gender:Male
  • Location:Hughesville ,MD

Posted 04 September 2012 - 02:56 PM

i know this is an old thread, but is this the one you traded to lyco? (here on techpb)

if so, the solenoid was missing a pin from inside
Sponsored By: ANSGear, Valken Paintball Southern Maryland Paintball
Posted Image
Bob Long 2k4 alias + freak + halo too

#15 SamBo

SamBo

    Junior Member

  • Players Club
  • PipPipPipPip
  • 880 posts
  • Gender:Male
  • Location:Stillwater, OK

Posted 04 September 2012 - 04:48 PM

Yeah he fixed it. I guess it chrono's right too?




2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users