Jump to content


Photo

TechPB recommended Marq & Intimidator Settings


  • Please log in to reply
53 replies to this topic

#1 efx*

efx*

    Member

  • Members
  • PipPip
  • 113 posts
  • Gender:Male
  • Location:Seminole, Florida aka the 727

Posted 26 September 2008 - 03:19 PM

Alright, here are some of my recomended settings for the Marq

LPR @ 80 to 85 psi (I run at 85psi for new guns, then drop down to 80psi after 30 cases)
HPR around 220psi (whatever to chrono)
Dwell @ 8ms

I usually lube the gun with lurker lube or mineral oil. If the gun is older, I use dow55

These guns are pretty tolerant so you can experiment


Very helpful thanks.
My sig was edited because it was not within the rules. Images used in signatures are to be less then Width of 600px, and height of 160px. Only ONE image is aloud in the signature, and it must be 30k or less. Only 5 lines of text are aloud. No text larger then size 2 is aloud in the signature.

I was a naughty boy and my image was larger than it was supposed to be. I got mowed by kitty.

#2 Pizzaluvr

Pizzaluvr

    Sophomore Member

  • Members
  • PipPipPip
  • 464 posts
  • Location:Fayetteville, AR

Posted 29 September 2008 - 08:19 PM

Are these for everyones settings? If so..

Stock Rapper
LPR: 75
HPR around 220, whatever it takes to chrono
Dwell stock(8 ms I think)

Team Fracture
B&E Paintball--Wild World Paintball

#3 eddiebelanger

eddiebelanger

    Newbie

  • Members
  • Pip
  • 14 posts

Posted 29 September 2008 - 08:23 PM

i just got my marq and have the lpr at about 83psi my hpr it set to chrono and dwell at 8 with dow 55 and tri-flow on bolt. im going to play 2m with it for the first time. wish me luck

#4 Alcatraz

Alcatraz

    Newbie

  • Members
  • Pip
  • 17 posts
  • Gender:Male
  • Location:Canada

Posted 29 September 2008 - 09:22 PM

Alright, here are some of my recomended settings for the Marq

LPR @ 80 to 85 psi (I run at 85psi for new guns, then drop down to 80psi after 30 cases)
HPR around 220psi (whatever to chrono)
Dwell @ 8ms

I usually lube the gun with lurker lube or mineral oil. If the gun is older, I use dow55

These guns are pretty tolerant so you can experiment


How about the setting with the new PE ???

#5 AndrewFalk

AndrewFalk

    Member

  • Members
  • PipPip
  • 234 posts
  • Gender:Male
  • Location:Newark

Posted 01 October 2008 - 11:11 AM

My personal setting with my Darq and Proficiency kit...

Dwell @ 6 ms
LPR @ 60 psi
HPR set to chrono at ~280 fps

Shoots amazing...I get about a hopper and 6 1/2 pods on my 48/45.



Images used in signatures are to be less than Width of 600px, and height of 160px. Only ONE image is allowed in the signature, and it must be 30k or less. Only 5 lines of text are allowed. No text larger then size 2 is allowed in the signature.

#6 Sin

Sin

    Member

  • Members
  • PipPip
  • 75 posts

Posted 05 October 2008 - 11:01 PM

I used the Rendition tech settings except I kept my dwell @ 8 ms. Chronographed my Alias to around 260 fps (shooting withing +-5) and I was getting 2 pods/2 hoppers per 1000 psi.

#7 trekari147

trekari147

    Newbie

  • Members
  • Pip
  • 2 posts

Posted 11 October 2008 - 07:59 PM

ok so i have a marq 6. how do i test the lpr and such... is there a certain tool or could i put any reg with a gauge on it and it will tell me? what should i do to get these settings?

#8 IrishBaller

IrishBaller

    Newbie

  • Members
  • Pip
  • 2 posts

Posted 11 October 2008 - 08:07 PM

probably a dumb question but where can i get lurker lube?

#9 alexrucco

alexrucco

    Member

  • Members
  • PipPip
  • 55 posts
  • Gender:Male

Posted 12 October 2008 - 03:05 PM

irishballer lurker has a wesite u can buy it there http://lurkerpaintball.com/ and trekari u can get a lpr tester from http://www.boblongdi...t...9&Itemid=93
why drink and drive when you can smoke and fly.

#10 IrishBaller

IrishBaller

    Newbie

  • Members
  • Pip
  • 2 posts

Posted 12 October 2008 - 04:29 PM

irishballer lurker has a wesite u can buy it there http://lurkerpaintball.com/ and trekari u can get a lpr tester from http://www.boblongdi...t...9&Itemid=93


ty

#11 adrenilanejunkie

adrenilanejunkie

    Sophomore Member

  • Members
  • PipPipPip
  • 673 posts
  • Gender:Male
  • Location:Las Vegas

Posted 12 October 2008 - 05:07 PM

what do vices that are broken in run at
Paintball: is my sport, is my passion, my life.
http://www.techpb.co...=0 Geo Owner


#12 AndrewFalk

AndrewFalk

    Member

  • Members
  • PipPip
  • 234 posts
  • Gender:Male
  • Location:Newark

Posted 15 October 2008 - 10:28 AM

what do vices that are broken in run at


70 psi stock. Or 60 psi with LP poppet.



Images used in signatures are to be less than Width of 600px, and height of 160px. Only ONE image is allowed in the signature, and it must be 30k or less. Only 5 lines of text are allowed. No text larger then size 2 is allowed in the signature.

#13 jp8290

jp8290

    Newbie

  • Members
  • Pip
  • 42 posts
  • Gender:Male
  • Location:Miami, FL.

Posted 16 October 2008 - 12:48 PM

where can i get a LPR gage for the marq at.

#14 spartan985

spartan985

    Newbie

  • Members
  • Pip
  • 31 posts

Posted 16 October 2008 - 06:46 PM

www.boblongdirect.com or call them up
MY girl play paintball. If your does too put this in your sig!
Pumpers unite!

#15 adrenilanejunkie

adrenilanejunkie

    Sophomore Member

  • Members
  • PipPipPip
  • 673 posts
  • Gender:Male
  • Location:Las Vegas

Posted 16 October 2008 - 06:47 PM

where can i get a LPR gage for the marq at.


http://www.boblongdi...t...6&Itemid=91
Paintball: is my sport, is my passion, my life.
http://www.techpb.co...=0 Geo Owner


#16 uncappedrampFTW

uncappedrampFTW

    Newbie

  • Members
  • Pip
  • 42 posts
  • Gender:Male
  • Location:Long Island NY

Posted 20 October 2008 - 03:50 PM

what are the rendition tech settings for the Vice because im blowing about 500 psi per hopper and thats horrible efficiency for a vice, i cant find any good settings for it so.....

#17 AndrewFalk

AndrewFalk

    Member

  • Members
  • PipPip
  • 234 posts
  • Gender:Male
  • Location:Newark

Posted 20 October 2008 - 05:36 PM

what are the rendition tech settings for the Vice because im blowing about 500 psi per hopper and thats horrible efficiency for a vice, i cant find any good settings for it so.....


Dwell @ 6 ms.
LPR @65 psi
HPR set to chrono.



Images used in signatures are to be less than Width of 600px, and height of 160px. Only ONE image is allowed in the signature, and it must be 30k or less. Only 5 lines of text are allowed. No text larger then size 2 is allowed in the signature.

#18 tothy

tothy

    Member

  • Members
  • PipPip
  • 108 posts
  • Gender:Male
  • Location:Scottsdale Arizona

Posted 22 October 2008 - 12:24 AM

Protege settings?



Images used in signatures are to be less than Width of 600px, and height of 160px. Only ONE image is allowed in the signature, and it must be 30k or less. Only 5 lines of text are allowed. No text larger then size 2 is allowed in the signature.

#19 AndrewFalk

AndrewFalk

    Member

  • Members
  • PipPip
  • 234 posts
  • Gender:Male
  • Location:Newark

Posted 24 October 2008 - 10:13 PM

Same exact settings as a Vice.



Images used in signatures are to be less than Width of 600px, and height of 160px. Only ONE image is allowed in the signature, and it must be 30k or less. Only 5 lines of text are allowed. No text larger then size 2 is allowed in the signature.

#20 tothy

tothy

    Member

  • Members
  • PipPip
  • 108 posts
  • Gender:Male
  • Location:Scottsdale Arizona

Posted 25 October 2008 - 08:23 PM

That's what i figured, just makin sure since there are some slight differences with the two

Thank you!



Images used in signatures are to be less than Width of 600px, and height of 160px. Only ONE image is allowed in the signature, and it must be 30k or less. Only 5 lines of text are allowed. No text larger then size 2 is allowed in the signature.

#21 JPRanger

JPRanger

    Member

  • Members
  • PipPip
  • 125 posts
  • Gender:Male
  • Location:MD

Posted 28 October 2008 - 07:04 PM

i just got a marq 7 and im new to these markers so idk my way around it yet, when i dry fire it the bolt barelly goes 4ward at all..all i can see is the very tip of the bolt when it fires...then when i fire faster and faster i start to see more and more of the bolt come forward, but if i keep going theres a loud pop..i have no idea what this is and honestly scared the shit out of me cuz i rlly dont wana break my new gun, please help

#22 cBomber220

cBomber220

    Newbie

  • Members
  • Pip
  • 8 posts

Posted 28 October 2008 - 11:13 PM

how about an infamous?

#23 Johnny G

Johnny G

    Member

  • Members
  • PipPip
  • 184 posts
  • Gender:Male
  • Location:Antigonish

Posted 29 October 2008 - 12:32 PM

what about setting for an 06 infamous with a virtue bored

#24 darkstar123481

darkstar123481

    Member

  • Members
  • PipPip
  • 264 posts
  • Gender:Male
  • Location:NJ

Posted 10 November 2008 - 10:41 PM

how else can i test my LPR without the LPR tester i dont feel like buying one its to expensive

#25 jp8290

jp8290

    Newbie

  • Members
  • Pip
  • 42 posts
  • Gender:Male
  • Location:Miami, FL.

Posted 10 December 2008 - 10:57 PM

thanks for the info

#26 cesar21

cesar21

    ¨SE HABLA ESPAÑOL¨

  • Members
  • PipPipPip
  • 382 posts
  • Gender:Male
  • Location:Holtville, Ca

Posted 04 January 2009 - 09:55 PM

which are the settings for the empire 2 intimidator?

#27 OverDose

OverDose

    I <3 My Quest

  • Members
  • PipPip
  • 117 posts
  • Gender:Male

Posted 04 January 2009 - 09:56 PM

any idea why my gun is now leaking from the feed neck i can hear it but not feel it =[
Posted Image
PAINTBALL&MOTOCROSS=MY LIFE


#28 ScaryJ

ScaryJ

    Member

  • Members
  • PipPip
  • 160 posts
  • Gender:Male
  • Location:West Sacramento, CA

Posted 13 January 2009 - 01:26 AM

Thanks i just set my new vice to settings here.
My Setup

Bob Long Vice-Black (laser 4c eyes,USB OLED Yakuza Board, Kila Dirty Bolt,
Kila magnet detents, Gear Drive on/off ASA, Low Pressure Poppet)
Pinokio Hopper with Virtue Speed Feed(ultra soft)
Crossfire 68/4500 carbon fiber
VForce Profiler

#29 LieutenantDan

LieutenantDan

    Senior Member

  • Members
  • PipPipPipPipPip
  • 1,373 posts
  • Gender:Male
  • Location:Briarcliff Manor, NY

Posted 17 January 2009 - 09:28 PM

How do i set the LPR?
Posted Image

My Feedback +5|-0
To HELL with georgia

#30 AndrewFalk

AndrewFalk

    Member

  • Members
  • PipPip
  • 234 posts
  • Gender:Male
  • Location:Newark

Posted 18 January 2009 - 08:59 PM

Get the LPR tester. The LPR is located beneath the barrel. You turn it in to increase pressure, and you back it out to decrease pressure.



Images used in signatures are to be less than Width of 600px, and height of 160px. Only ONE image is allowed in the signature, and it must be 30k or less. Only 5 lines of text are allowed. No text larger then size 2 is allowed in the signature.

#31 themonkman

themonkman

    Sophomore Member

  • Members
  • PipPipPip
  • 472 posts
  • Gender:Male

Posted 01 February 2009 - 01:59 AM

how else can i test my LPR without the LPR tester i dont feel like buying one its to expensive


You can't reliably set your LPR without an LPR gauge. Depending on your marker you could find out what the typical stock setting is from the flush position of the adjustment screw on the LPR. For the Vice and Protege's LPR it's about 1 1/2 turns in from flush. From there you fine tune and adjust with the LPR tester.
If your LPR is way off it can throw off the HPR, and vice versa.
<a href="http://&quot;http://www.socalghosts.com" target="_blank"><img src="http://i713.photobuc...stsbanner2.jpg" border="0" class="linked-sig-image" /></a>

<!--sizeo:2--><span style="font-size:10pt;line-height:100%"><!--/sizeo--><a href="http://www.SoCalGhosts.com" target="_blank">www.SoCalGhosts.com</a> - Proudly Sponsored by: ANS Gear <a href="http://www.ANSGEAR.com" target="_blank">www.ANSGEAR.com</a> and Save Phace <a href="http://www.SAVEPHACE.com" target="_blank">www.SAVEPHACE.com</a><!--sizec--></span><!--/sizec-->

<!--sizeo:2--><span style="font-size:10pt;line-height:100%"><!--/sizeo-->Mike Phillips: "Pound for pound - Bob Long Vice, one of the best guns on the market...ever! This gun is absolutely absurd."<!--sizec--></span><!--/sizec-->

#32 PeterV

PeterV

    Don't fuck with Bob Long

  • Members
  • PipPipPip
  • 411 posts
  • Gender:Male
  • Location:Decatur IL

Posted 11 March 2009 - 06:55 PM

Hey i have the alias and it doesn't seem to want the dwell to go any lower than 104.0 ms any idea i have the rl eddition
<img src="http://i725.photobuc...bSignature.gif" border="0" class="linked-sig-image" />
<a href="http://www.techpb.co...howtopic=39853" target="_blank"><!--sizeo:2--><span style="font-size:10pt;line-height:100%"><!--/sizeo--><!--coloro:#ff0000--><span style="color:#ff0000"><!--/coloro--><!--fonto:Comic Sans MS--><span style="font-family:Comic Sans MS"><!--/fonto-->Proud owner of an Russian Legion Timmy. <!--fontc--></span><!--/fontc--><!--colorc--></span><!--/colorc--><!--sizec--></span><!--/sizec--></a> <!--sizeo:1--><span style="font-size:8pt;line-height:100%"><!--/sizeo--><!--coloro:#006400--><span style="color:#006400"><!--/coloro--><!--fonto:Comic Sans MS--><span style="font-family:Comic Sans MS"><!--/fonto-->Fat Ballers club<!--fontc--></span><!--/fontc--><!--colorc--></span><!--/colorc--> <!--sizec--></span><!--/sizec-->

#33 gamer565

gamer565

    Member

  • Banned
  • PipPip
  • 63 posts
  • Gender:Male

Posted 12 March 2009 - 12:28 AM

Hey i have the alias and it doesn't seem to want the dwell to go any lower than 104.0 ms any idea i have the rl eddition


your dwell is at 4ms...raise it to 8

the "1" is actually another "L"...since dwell is spelled with 2 L's and not one...


edit: btw Mike, you dont but dow55 on everything. you use triflow(or some paintball oil) on the bolt orings. putting dow on the delrin bolt will cause it to swell and drag. therefor leading other major problems.

Edited by gamer565, 12 March 2009 - 12:31 AM.

forum troll

#34 zop1o

zop1o

    megasuperawesomelazerbeamrailgun ofepicdoomandstuff

  • Members
  • PipPipPipPipPipPip
  • 3,585 posts
  • Gender:Male
  • Location:The snake

Posted 02 April 2009 - 08:46 PM

isnt there different settings for the marq proficiency engine? i thought i read somewhere it was like, 70 or 75 or something on the lpr and 180 ish on the hpr.
Marq's men founder. flex owner. I AM A MUPPET! C.O.C. member 91. pump/stock players president. Karnivor Owner councilman. Old School Owner. GUN WHORE.
Posted Image
zop1o's marq and auto cocker tuning and repair services
zop1o's feedback2/0/0

#35 juit

juit

    Member

  • Members
  • PipPip
  • 136 posts
  • Gender:Male
  • Location:Texas

Posted 06 April 2009 - 11:43 AM

what do vices that are broken in run at


70 PSI stock. Or 60 psi with LP poppet.



NO NO NO DUDE! your LPR pressure doesn't need to be change when you get the LP valve since its longer it will need the same amount of pressure for the ram travel with out any problem

I have mine on 65 PSI for both type of valve

175 PSI on the HPR with LP valve

215 PSI with HP valve

8 dwell same for both

thin coat of dow 55 and ram the ram must be grease free on both ends, you will need to relub it more times than a thick coat but you wont get first drop off shoot

Please use triflow on the bolt 2-3 drops and make a thin even coat

Why Triflow? Firs it has Teflon and will make your bolt enclosure last more. Second Triflow repels dust and wont end up on your marker eyes
I love this sport!

#36 Kowz_76

Kowz_76

    Accept no imitations

  • Members
  • PipPipPip
  • 533 posts
  • Gender:Male
  • Location:Midcoast Maine, bub

Posted 26 April 2009 - 09:39 PM

isnt there different settings for the marq proficiency engine? i thought i read somewhere it was like, 70 or 75 or something on the lpr and 180 ish on the hpr.

You're exactly right. Once it's broken in you can lower the lpr a little. Also make sure you run your dwell at 6 instead of 8. Some people use 7 while breaking it in.
New England Blizzard Proudly sponsored by:
Bob Long
Kohn Sports

#37 android17ak47

android17ak47

    Sophomore Member

  • Members
  • PipPipPip
  • 681 posts
  • Gender:Male
  • Location:Jamestown, New York

Posted 13 June 2009 - 10:58 PM

Im getting great results with my alias with the following settings and this is with stock lpr, stock torpedo hpr, stock ram, stock bolt, lucky board w/virtue programming.

dwell 9ms(value 10 on virtue)
lpr 80psi
eye delay 3ms
anti bolt stick off(no fsdo)
hpr at 155psi 290-300fps
efficiency with 45/45: half a case from 3,000psi with about 200psi left after test. paint used for test: anarchy with dye boomstick 689

Oddly enough my ashcroft 0-300psi gauge read 155psi on my torpedo regulator when I set my alias to shoot at 300fps with all stock parts and settings. I dont have a volumizer or a light poppet spring, its all alias stock internals. IDC about getting the lowest settings on my hpr so I have no reason to make up 155psi in case anyone thought twice about that claim.

#38 PayntBawler

PayntBawler

    Newbie

  • Members
  • Pip
  • 31 posts
  • Location:Tampa, FL

Posted 07 August 2009 - 02:41 PM

Can i use sl33k lube on my marq 6??

#39 hipnopath

hipnopath

    Cut it up Fresh.

  • Members
  • PipPipPipPipPip
  • 1,194 posts
  • Gender:Male
  • Location:San Antonio, Texas

Posted 22 August 2009 - 11:59 AM

Can i use sl33k lube on my marq 6??


Nope. I have new settings:

Lighter Poppit Spring

Dwell: 5

LPR: 50

HPR: 190

275 FPS.

#40 tiny5815

tiny5815

    _1sO

  • Members
  • PipPipPipPipPip
  • 1,092 posts
  • Gender:Male
  • Location:San Jacinto, California

Posted 10 January 2010 - 02:21 PM

which pressure tester do I use for my alias? Bob Long Direct Link

#41 gamer575

gamer575

    Newbie

  • Members
  • Pip
  • 48 posts

Posted 10 January 2010 - 05:28 PM

which pressure tester do I use for my alias? Bob Long Direct Link



You dont need a tester for gen3's since there is already a lpr gauge on the front block...

I recommend downloading and reading the gen3 manual..

#42 DFSniper

DFSniper

    Member

  • Members
  • PipPip
  • 52 posts

Posted 15 April 2010 - 05:03 PM

Alias factory settings:
LPR @ 70-80
HPR @ 200-280
Dwell @ 8
BIP @ 0.5
Bolt Delay @ 15
Debounce @ 12
MBounce @ 2
Delay @ 10

Who is but the form following the function of what, and what I am is a man in a mask. Posted Image


#43 INVERTminihelp

INVERTminihelp

    i love MARQS!

  • Members
  • PipPipPipPipPip
  • 1,456 posts
  • Gender:Male
  • Location:orland PA

Posted 20 April 2010 - 09:12 PM

i put my mummy at 80psi on the lpr and it shoots money,tits,wahtever
Posted Image
Feedback 2/0/0

#44 protofreak

protofreak

    Member

  • Members
  • PipPip
  • 276 posts
  • Gender:Male
  • Location:humble texas

Posted 11 June 2010 - 11:54 PM

im getting a ripper 2 in a trade what setting should i use and what manual goes with it

im new to bob long guns
dye dm12,dm3 and proto rail, bl ripper 2
St. louis Alvalanche fan #13
http://s195.photobuc...236/Fragmortus/
http://www.pbreview....p;userid=156696

#45 Az P8ntballer

Az P8ntballer

    Ballers in Action

  • Members
  • PipPipPip
  • 557 posts
  • Gender:Male

Posted 19 July 2010 - 11:39 PM

mike i had a rl timmy and teched it the way u do and loved it im now trading my shocker and prostock pump for a hybrid mummy im deff gonna tech it this way

#46 Melendez402

Melendez402

    El Dorado

  • Members
  • PipPipPip
  • 510 posts
  • Gender:Male
  • Location:USA

Posted 09 May 2011 - 07:21 PM

Any good settings for a G6R?

#47 Bajrx2

Bajrx2

    Remember Mike is ALWAYS! Watching

  • Members
  • PipPipPip
  • 517 posts
  • Gender:Male
  • Location:Tarpon Springs, Florida

Posted 11 July 2011 - 11:22 AM

I need 2k5'd Dragon Intimidator settings plz pm me the settings thank you

Edited by Bajrx2, 11 July 2011 - 06:01 PM.

Posted Image
REQUIESCAT EN PACE BORG SIAMO TUTTI BORG

#48 Geoffcuz

Geoffcuz

    Newbie

  • Members
  • Pip
  • 26 posts

Posted 18 July 2011 - 02:22 AM

Any Settings for the Mtac ?

#49 Shamrock905

Shamrock905

    Junior Member

  • Members
  • PipPipPipPip
  • 808 posts
  • Gender:Male
  • Location:San Diego, CA

Posted 24 January 2012 - 05:58 PM

These Alias settings work for a 2k6 Timmy? Cuz I need some help.....
2k6 Bob Long Intimidator-CP 14' .685 barrel, Pinokio, Ninja 68/4500
2k2 Cocker Pump-Hooptie Pump Kit, CCM Dust Black 86 degree trigger frame, CP 14' .685 barrel, CP Rail, CP Reg, Check-It Delrin Bolt, Ninja 13/3000 HPA tank, Pocket Hoppers.......

#50 MedevilMIke

MedevilMIke

    Sophomore Member

  • Players Club
  • PipPipPip
  • 351 posts
  • Gender:Male
  • Location:Massachusetts


Posted 25 January 2012 - 01:05 PM

Can i use sl33k lube on my marq 6??


Nope. I have new settings:

Lighter Poppit Spring

Dwell: 5

LPR: 50

HPR: 190

275 FPS.


why can't you use sl33k on a marq 6?




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users