Jump to content


Photo

Tips on what parts to use to make mags


  • Please log in to reply
8 replies to this topic

#1 get.lit.up!

get.lit.up!

    200lb of unpredictable coming to hunt ya ;)

  • Members
  • PipPipPipPipPipPip
  • 3,703 posts
  • Gender:Male

Posted 09 December 2012 - 11:40 PM

Hey does anyone have tips on parts to use to make PumpMags or EgoMags (or Electro Pneumatic Mags in general)?

PumpMag:
-Would a X-Valve be overkill or will a classic valve with L10 bolt be sufficient?
-Does anyone else offer a GOOD pump kit compatible with CCM handles other than rainman?
-What 86* frame will work on a Mag? Is there a single trigger Y frame available for purchase?
-Should I buy a classic mag, put a ULE body on it, then send it to rainman or Luke to mill it for a pump kit?

EgoMag:
-What frame should I use? I can get my hand on a aurora Etek frame easily at the moment (I so want a star frame though)
-Is a PPS Pebble the recommend LPR? What other quality LPR should I check out?
-Alternatives for the SMC SY113A-SG-PM3 noid?
-Any Alternative to the MPA-3?
-Is a QEV recommended or required?
-What Rail should I get?
-Anything else I'm missing? (ULE mainbody, Xvalve, trigger frame, rail, LPR, solenoid, ram, pops asa, bike grip, vert. asa, CCM macro fittings, CCM feedleck with locklever, freak barrel)

If you want to give a crash course on PumpMags and/or elecropneu mags please do, I would LOVE to hear it!

NOTE: I'm just collecting cheap parts starting February after I get my S6 or J12(unless I find something uber cheap), until I can acquire an assload of cash.

gnUDL.png
See my about me for useful things like feedback!

#2 WiscoBaller

WiscoBaller

    Master Member

  • TechPB Players Club
  • PipPipPipPipPipPip
  • 2,655 posts
  • Gender:Male

Posted 09 December 2012 - 11:52 PM

Hey does anyone have tips on parts to use to make PumpMags or EgoMags (or Electro Pneumatic Mags in general)?

PumpMag:
-Would a X-Valve be overkill or will a classic valve with L10 bolt be sufficient?
Xvalve is not huge in pump as it is more of a Rate of Fire option.
-Does anyone else offer a GOOD pump kit compatible with CCM handles other than rainman?
Dont know
-What 86* frame will work on a Mag? Is there a single trigger Y frame available for purchase?
Do not believe so, but I would assume someone like acid could make a single finger trigger for it
-Should I buy a classic mag, put a ULE body on it, then send it to rainman or Luke to mill it for a pump kit?
That would probably be best, but you would also need to send the rail in.

EgoMag:
-What frame should I use? I can get my hand on a aurora Etek frame easily at the moment (I so want a star frame though)
Star frames are hard to find, but a lot of people part the egomags, and you should be able to find one.
-Is a PPS Pebble the recommend LPR? What other quality LPR should I check out?
I have heard good things about the Dragunfly LPR's, work better than ticklers, and I think Renie? made an internal LPR foregrip from the Dragunfly design.
-Alternatives for the SMC SY113A-SG-PM3 noid?
I'd leave it as is, and get one that works. have heard something about the trilogy select fire noids.
-Any Alternative to the MPA-3?
Again, trilogy select fire noids
-Is a QEV recommended or required?
Dont think either or, barbs are normally used
-What Rail should I get?
Any rail you want, you mod the frame, not the rail.
-Anything else I'm missing? (ULE mainbody, Xvalve, trigger frame, rail, LPR, solenoid, ram, pops asa, bike grip, vert. asa, CCM macro fittings, CCM feedleck with locklever, freak barrel)
Cocker tubing, set screws, sear, board, different asa depending on how you plan to run the LPR (seen most of them run off the asa with a 90* fitting)

If you want to give a crash course on PumpMags and/or elecropneu mags please do, I would LOVE to hear it!

NOTE: I'm just collecting cheap parts starting February after I get my S6 or J12(unless I find something uber cheap), until I can acquire an assload of cash.


University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST


#3 get.lit.up!

get.lit.up!

    200lb of unpredictable coming to hunt ya ;)

  • Members
  • PipPipPipPipPipPip
  • 3,703 posts
  • Gender:Male

Posted 10 December 2012 - 12:05 AM

Would love something like this but with my personal touches

Posted Image
gnUDL.png
See my about me for useful things like feedback!

#4 kingJurzy

kingJurzy

    OFFICIAL TechPB's best member 2012

  • Members
  • PipPipPipPipPipPipPipPip
  • 9,071 posts
  • Gender:Male
  • Location:Bay Area, California


Posted 10 December 2012 - 01:04 AM

Would love something like this but with my personal touches

Posted Image


Posted ImagePosted ImagePosted ImagePosted Image

FEEDBACK: 23/0/0


#5 get.lit.up!

get.lit.up!

    200lb of unpredictable coming to hunt ya ;)

  • Members
  • PipPipPipPipPipPip
  • 3,703 posts
  • Gender:Male

Posted 10 December 2012 - 01:09 AM

Just heard that a axe mag is also possible. Looking into it

Edit: new take on a minimag lol

Posted Image

Edited by get.lit.up!, 10 December 2012 - 08:58 AM.

gnUDL.png
See my about me for useful things like feedback!

#6 WiscoBaller

WiscoBaller

    Master Member

  • TechPB Players Club
  • PipPipPipPipPipPip
  • 2,655 posts
  • Gender:Male

Posted 10 December 2012 - 10:32 AM

I think that is an 05 ego frame, not an etek frame. Another good option for having a screen.

University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST


#7 get.lit.up!

get.lit.up!

    200lb of unpredictable coming to hunt ya ;)

  • Members
  • PipPipPipPipPipPip
  • 3,703 posts
  • Gender:Male

Posted 10 December 2012 - 02:08 PM

If I can pick up a star frame with everything then I would, but I think a ego 5/6 frame would work
gnUDL.png
See my about me for useful things like feedback!

#8 WiscoBaller

WiscoBaller

    Master Member

  • TechPB Players Club
  • PipPipPipPipPipPip
  • 2,655 posts
  • Gender:Male

Posted 19 December 2012 - 01:14 PM

there is a smokin deal on an egomag frame complete on AO right now.

University of Wisconsin Whitewater Paintball Club
Sponsored by KEE, H2 Paintball, Empire
The Hooligans Paintball Team
Bob Long Victory Ripper Dye Rotor Dye Throttle 70/4500
Bob Long Ripper FST


#9 Dev.

Dev.

    Totally a sophomore member

  • Members
  • PipPipPip
  • 599 posts
  • Gender:Male
  • Location:wat


Posted 05 January 2013 - 01:07 PM

Most everything has been answered but to your question about the 86 frame, it is possible with the ccm 86 frame, just requires an extensive amount of modifications

PonyBounceSig.gif





1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users