Jump to content


Photo

gog envy leak


  • Please log in to reply
9 replies to this topic

#1 pc_baller

pc_baller

    Member

  • Members
  • PipPip
  • 221 posts
  • Gender:Male
  • Location:panama city beach ,FL

Posted 24 March 2013 - 06:35 PM

my friends gog envy is leaking from the pressure release hole on the reg and i just relubed and changed the o-rings in the reg and it was pouring out air now its not as bad but still leaks and if i fire it it stops leaking for a few seconds and then starts leaking again.

i need some help asap
+2/-0my feedback


First gain the victory and then make the best use of it---Horatio Nelson


#2 TacticlTwinkie

TacticlTwinkie

    *insert witty title*

  • Members
  • PipPipPipPipPipPip
  • 3,974 posts
  • Gender:Male
  • Location:Surf City, USA

Posted 24 March 2013 - 06:37 PM

Is he using co2 or hpa?

#3 pc_baller

pc_baller

    Member

  • Members
  • PipPip
  • 221 posts
  • Gender:Male
  • Location:panama city beach ,FL

Posted 24 March 2013 - 06:39 PM

hpa and ive rebuilt the damn reg like 5 times replace all the orings and lubed it up good it's not leaking near as bad but before it was a constant leak now its only when not shooting

Edited by pc_baller, 24 March 2013 - 06:40 PM.

+2/-0my feedback


First gain the victory and then make the best use of it---Horatio Nelson


#4 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 22,000 posts
  • Gender:Female
  • Location:Your bedroom


Posted 24 March 2013 - 06:45 PM

If it's leaking out the bleed hole, then it's pretty much either the piston o-ring, or the rear seal o-ring that sits in the spring platform.

Edited by andrewthewookie, 24 March 2013 - 06:46 PM.

RebelSignaturejedicode-1.jpg
Hybrid SFT 09 Impulse HB REV-i Macroless Mech Ion
Rotor Grillz PE 70/45 Feedback - 23/0/0

Closer & Angel A1 F/S/T


#5 G4paintballer

G4paintballer

    Gun/gear whore

  • Members
  • PipPipPipPipPipPipPip
  • 5,862 posts
  • Gender:Male
  • Location:Western Wisconsin

Posted 24 March 2013 - 07:24 PM

Have you tried adjusting the reg? I know if it's turned one way all the way it leaks.
Current setup: WGP Trilogy, CCM S6, Ion Xe
Feedback 10/0/0

#6 pc_baller

pc_baller

    Member

  • Members
  • PipPip
  • 221 posts
  • Gender:Male
  • Location:panama city beach ,FL

Posted 24 March 2013 - 07:42 PM

i got it i just lubed it up like crazy and it stopped leaking
+2/-0my feedback


First gain the victory and then make the best use of it---Horatio Nelson


#7 mustangs

mustangs

    "Everyone has a plan, until they get hit in the face"

  • Members
  • PipPipPipPipPip
  • 1,177 posts
  • Gender:Male
  • Location:New Jersey

Posted 24 March 2013 - 11:23 PM

Make sure the gun shoots and cycles fine. Also if you can chrono it again it would help so you know it can shoot at 280 without a problem and you don't have any velocity spikes



#8 pc_baller

pc_baller

    Member

  • Members
  • PipPip
  • 221 posts
  • Gender:Male
  • Location:panama city beach ,FL

Posted 25 March 2013 - 11:29 PM

fauk me now its leaking from the bolt ive replaced both the inner and outer bolt stop orings and its still leaking and if i put my finger in the bolt and push it up while aired up it stops until i shoot it
+2/-0my feedback


First gain the victory and then make the best use of it---Horatio Nelson


#9 mustangs

mustangs

    "Everyone has a plan, until they get hit in the face"

  • Members
  • PipPipPipPipPip
  • 1,177 posts
  • Gender:Male
  • Location:New Jersey

Posted 26 March 2013 - 12:09 AM

You really need to call GOG. What kind of lube are you using?



#10 pc_baller

pc_baller

    Member

  • Members
  • PipPip
  • 221 posts
  • Gender:Male
  • Location:panama city beach ,FL

Posted 26 March 2013 - 12:31 AM

You really need to call GOG. What kind of lube are you using?



i fixed it FINALLY there was an oring behind the feedneck in the breech that needed changing....i didnt even know that was there

Edited by pc_baller, 26 March 2013 - 12:32 AM.

+2/-0my feedback


First gain the victory and then make the best use of it---Horatio Nelson





2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users