Jump to content


Photo

Macdev Droid


  • Please log in to reply
15 replies to this topic

#1 NJC

NJC

    pumper

  • Members
  • PipPipPipPipPipPip
  • 3,395 posts
  • Gender:Male
  • Location:Utah

Posted 06 May 2013 - 09:12 PM

i own a macdev droid and by bolt will not cycle fully. it will not fire a shot. i have cleaned, relubed, and replaced all the o-rings on the drive train and bolt but the issue persists. i have also cleaned and relubed the regulator and replaced the battery. The bolt will only go just far enough to touch the ball, and occasionally push it past the detents. and make a very small puff noise, not the sound of the marker firing a ball.If i pull the trigger above about 15 bps the bolt sticks forward and creates a massive leak.i do not know what to do.

I split my vote, half for etekgirl's body, half for her mind, because I respect a woman's mind just as much as her cans.
*Waits to get hit*


#2 BurningPlaydoh

BurningPlaydoh

    Blow-dough'ed

  • Members
  • PipPipPipPipPipPipPip
  • 6,105 posts
  • Gender:Male
  • Location:Twin Cities, MN

Posted 06 May 2013 - 09:30 PM

Try another tank.

#3 syllabuz

syllabuz

    Just Keepin' It Real...

  • Members
  • PipPip
  • 157 posts
  • Gender:Male

Posted 06 May 2013 - 09:35 PM

i own a macdev droid and by bolt will not cycle fully. it will not fire a shot. i have cleaned, relubed, and replaced all the o-rings on the drive train and bolt but the issue persists. i have also cleaned and relubed the regulator and replaced the battery. The bolt will only go just far enough to touch the ball, and occasionally push it past the detents. and make a very small puff noise, not the sound of the marker firing a ball.If i pull the trigger above about 15 bps the bolt sticks forward and creates a massive leak.i do not know what to do.


check the bolt switch/ bolt sail oring.
reset your board to factory settings. go from there.

POS


#4 NJC

NJC

    pumper

  • Members
  • PipPipPipPipPipPip
  • 3,395 posts
  • Gender:Male
  • Location:Utah

Posted 06 May 2013 - 10:12 PM

i have switched all the bolt o-rings and used 2 different, high pressure tanks

I split my vote, half for etekgirl's body, half for her mind, because I respect a woman's mind just as much as her cans.
*Waits to get hit*


#5 syllabuz

syllabuz

    Just Keepin' It Real...

  • Members
  • PipPip
  • 157 posts
  • Gender:Male

Posted 06 May 2013 - 10:19 PM

i have switched all the bolt o-rings and used 2 different, high pressure tanks


do you have a gold bolt?
what version of valve do you have?

POS


#6 NJC

NJC

    pumper

  • Members
  • PipPipPipPipPipPip
  • 3,395 posts
  • Gender:Male
  • Location:Utah

Posted 06 May 2013 - 10:27 PM


i have switched all the bolt o-rings and used 2 different, high pressure tanks


do you have a gold bolt?
what version of valve do you have?

yes i have the gold bolt. unsure which valve

I split my vote, half for etekgirl's body, half for her mind, because I respect a woman's mind just as much as her cans.
*Waits to get hit*


#7 Praetorian

Praetorian

    Skill? Where can I buy that?!

  • Members
  • PipPipPipPipPip
  • 1,273 posts
  • Gender:Male
  • Location:Dead Box

Posted 06 May 2013 - 10:30 PM

What uhm... Settings are on your board? They stock or have you messed with them?

#8 BurningPlaydoh

BurningPlaydoh

    Blow-dough'ed

  • Members
  • PipPipPipPipPipPipPip
  • 6,105 posts
  • Gender:Male
  • Location:Twin Cities, MN

Posted 06 May 2013 - 10:58 PM

Is your HPR set high enough?

#9 Panda's Revenge

Panda's Revenge

    Officially Sponsored by China Ball

  • Members
  • PipPipPipPipPipPip
  • 3,495 posts
  • Gender:Female
  • Location:San Diego


Posted 07 May 2013 - 08:17 AM

Check all settings on the board. Might be your dwell is too low.

#10 NJC

NJC

    pumper

  • Members
  • PipPipPipPipPipPip
  • 3,395 posts
  • Gender:Male
  • Location:Utah

Posted 07 May 2013 - 05:31 PM

board is set with a very high dwell, 28. HPR i turned up so much is leaked until i turned it down. no change

I split my vote, half for etekgirl's body, half for her mind, because I respect a woman's mind just as much as her cans.
*Waits to get hit*


#11 syllabuz

syllabuz

    Just Keepin' It Real...

  • Members
  • PipPip
  • 157 posts
  • Gender:Male

Posted 07 May 2013 - 05:57 PM

if you have a reg tester, set your HPR to 90-110.
and turn down your dwell to 12-13. or just reset your board.
check under the bolt orings for cracks, same for the valve.

POS


#12 NJC

NJC

    pumper

  • Members
  • PipPipPipPipPipPip
  • 3,395 posts
  • Gender:Male
  • Location:Utah

Posted 07 May 2013 - 06:08 PM

if you have a reg tester, set your HPR to 90-110.
and turn down your dwell to 12-13. or just reset your board.
check under the bolt orings for cracks, same for the valve.


what do you mean by cracks, as in cracks in the metal?

I split my vote, half for etekgirl's body, half for her mind, because I respect a woman's mind just as much as her cans.
*Waits to get hit*


#13 syllabuz

syllabuz

    Just Keepin' It Real...

  • Members
  • PipPip
  • 157 posts
  • Gender:Male

Posted 07 May 2013 - 06:23 PM


if you have a reg tester, set your HPR to 90-110.
and turn down your dwell to 12-13. or just reset your board.
check under the bolt orings for cracks, same for the valve.


what do you mean by cracks, as in cracks in the metal?


yup.

POS


#14 NJC

NJC

    pumper

  • Members
  • PipPipPipPipPipPip
  • 3,395 posts
  • Gender:Male
  • Location:Utah

Posted 07 May 2013 - 08:18 PM

i have not seen something like this before on any of my friends' guns. the bolt will not go all the way forward, as if something is holding the bolt back

I split my vote, half for etekgirl's body, half for her mind, because I respect a woman's mind just as much as her cans.
*Waits to get hit*


#15 Praetorian

Praetorian

    Skill? Where can I buy that?!

  • Members
  • PipPipPipPipPip
  • 1,273 posts
  • Gender:Male
  • Location:Dead Box

Posted 07 May 2013 - 08:57 PM

it's gadda be a Valve cracked. Just trying to picture where the "Stop" is coming from, and their maybe a crack, or... your solenoid maybe dead.

#16 CaptainKay

CaptainKay

    Newbie

  • Members
  • Pip
  • 7 posts

Posted 05 September 2013 - 01:44 AM

I'm a Droid owner too. Out of curiosity, how did you fare with this?




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users