Jump to content


Photo

Spyder vs1 solenoid not releasi


  • Please log in to reply
6 replies to this topic

#1 Djtris

Djtris

    Newbie

  • Members
  • Pip
  • 4 posts

Posted 29 July 2013 - 02:15 PM

My vs1 is having an issue with the solenoid not releasing the sear, this started happening after I put in a virtue board. Also the bolt will not stay cocked not sure if the solenoid is cause for this issue. Any feedback I will be greatful.

Edited by Djtris, 29 July 2013 - 02:19 PM.


#2 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 21,872 posts
  • Gender:Female
  • Location:Your bedroom


Posted 29 July 2013 - 02:21 PM

The solenoid not releasing sounds like a low battery issue.

 

With the not recocking, exactly how is it not recocking? Does the gun shoot at velocity, but the hammer fails to catch and jackhammers? Does the paintball not reach velocity and the hammer just kind of sticks forward?


RebelSignaturejedicode-1.jpg
Hybrid SFT • 09 Impulse • HB REV-i • Macroless Mech Ion
Rotor • Grillz • PE 70/45 • Feedback - 23/0/0

Fear is the mind-killer


#3 Djtris

Djtris

    Newbie

  • Members
  • Pip
  • 4 posts

Posted 29 July 2013 - 05:11 PM

The hammer will not catch on the sear, battery is fully charged

Edited by Djtris, 29 July 2013 - 05:21 PM.


#4 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 21,872 posts
  • Gender:Female
  • Location:Your bedroom


Posted 29 July 2013 - 05:20 PM

I'd check to make sure there's no wires or anything like that obstructing the solenoid/sear and holding it down, and also make sure it or the hammer aren't starting to round off.


Edited by andrewthewookie, 29 July 2013 - 05:20 PM.

RebelSignaturejedicode-1.jpg
Hybrid SFT • 09 Impulse • HB REV-i • Macroless Mech Ion
Rotor • Grillz • PE 70/45 • Feedback - 23/0/0

Fear is the mind-killer


#5 Djtris

Djtris

    Newbie

  • Members
  • Pip
  • 4 posts

Posted 29 July 2013 - 05:24 PM

Thanks will check that out

#6 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 21,872 posts
  • Gender:Female
  • Location:Your bedroom


Posted 29 July 2013 - 05:29 PM

Also, while you're in the guts, might as well check the o-ring on the hammer and see if that's good or not.


RebelSignaturejedicode-1.jpg
Hybrid SFT • 09 Impulse • HB REV-i • Macroless Mech Ion
Rotor • Grillz • PE 70/45 • Feedback - 23/0/0

Fear is the mind-killer


#7 Djtris

Djtris

    Newbie

  • Members
  • Pip
  • 4 posts

Posted 30 July 2013 - 04:25 PM

It ended up being the sear spring, thank you for the suggestions




2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users