Jump to content


Photo

Techt L7 bolt sticking forward in GOG Extcy

Extcy Gog L7 Techt Virtue

  • Please log in to reply
6 replies to this topic

#1 1stFlight2Vegas

1stFlight2Vegas

    Newbie

  • Members
  • Pip
  • 9 posts

Posted 26 January 2014 - 07:03 PM

So i just upgraded my Extcy with a Virtue Board, Virtue Eyes, and techt L7 bolt and everything seams to be running smoothly except for one thing. (I also already have 360 Qev)

So i have the dwell set at 14 which is 4 above the lowest setting that the bolt actually does a full cycle.

But for some reason when i rip a nice stream of paint on about the 12-20th shot fired the bolt stays forward and allows for the air to just dump out the barrel . The bolt will stay forward until i pull the trigger again and then it just works fine until i rip another stream of paint then it does the same thing.

I have lubed up the gun 2 separate times and the issue still seems to continue.

Any help or ideas would be Great! Thank you

#2 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 21,993 posts
  • Gender:Female
  • Location:Your bedroom


Posted 26 January 2014 - 07:20 PM

It sounds like the solenoid could be sticking open. Does the Virtue board come with its own solenoid, or do you use the one that came with the Extcy?


RebelSignaturejedicode-1.jpg
Hybrid SFT 09 Impulse HB REV-i Macroless Mech Ion
Rotor Grillz PE 70/45 Feedback - 23/0/0

Closer & Angel A1 F/S/T


#3 1stFlight2Vegas

1stFlight2Vegas

    Newbie

  • Members
  • Pip
  • 9 posts

Posted 26 January 2014 - 07:30 PM

Im using the original soleniod that came with the extcy, but im not leaning towards the solenoid because it worked flawlessly with the blackheart board.... I also noticed slight wear on the L7 bolt towards the front after running about 4 hoppers threw it but i figured thats normal because the stock bolt had wear too. Ive been scratching my head with it for about a week now

#4 andrewthewookie

andrewthewookie

    Shaaaaaaaaaaaaaaaaarks :(

  • Chat Coordinator
  • PipPipPipPipPipPipPipPip
  • 21,993 posts
  • Gender:Female
  • Location:Your bedroom


Posted 26 January 2014 - 07:34 PM

Hmm... What size barrel do you have? Is it a really small bore?


RebelSignaturejedicode-1.jpg
Hybrid SFT 09 Impulse HB REV-i Macroless Mech Ion
Rotor Grillz PE 70/45 Feedback - 23/0/0

Closer & Angel A1 F/S/T


#5 1stFlight2Vegas

1stFlight2Vegas

    Newbie

  • Members
  • Pip
  • 9 posts

Posted 26 January 2014 - 07:36 PM

I actually used the stock barrel just to test the gun after the upgrades i believe its a .693 also it was really cold out if that makes a difference... About 20 degrees out

#6 Punisher068

Punisher068

    Member

  • Members
  • PipPip
  • 216 posts
  • Gender:Male
  • Location:Santa Cruz Mountains

Posted 27 January 2014 - 11:23 AM

There's some compatibility issues with the L7 and Virtue boards.Change your dwell up or down a point or two.Should fix the problem.Not sure exactly why this is,there's a sticky on PBN about it.Nothing serious to worry about.Oddly my 07 PMR with a Virtue&TechT did the same thing



#7 1stFlight2Vegas

1stFlight2Vegas

    Newbie

  • Members
  • Pip
  • 9 posts

Posted 27 January 2014 - 01:06 PM

Ok cool, thanks a lot guys I'll play with the dwell when I get a chance to grab some more air and let you know how that works.





Also tagged with one or more of these keywords: Extcy, Gog, L7, Techt, Virtue

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users