Jump to content


Photo

G6r LPR Setting

LRP G6r Bob Long Pressure

  • Please log in to reply
7 replies to this topic

#1 Bunkee

Bunkee

    Newbie

  • Members
  • Pip
  • 4 posts

Posted 02 April 2014 - 10:37 AM

Reading the Manual and Watching the TechPB video on the G6r and wanted to know the process of finding the best LPR setting for my gun. I use an SLP reg on my tank.

 

Do I first adjust my HPR and THEN go and see how low I can adjust my reg without compromising the consistency? 

 

Basically I am trying to get the smoothest most consistent shot possible and don't know if there is a "set" output pressure I can count on or if it truly depends on each G6r.

 

Thanks for your help TPBC

 

-Bunk



#2 SPARTAN1147789

SPARTAN1147789

    SPARTAN

  • Members
  • PipPipPipPip
  • 751 posts
  • Gender:Male

Posted 02 April 2014 - 11:44 AM

Your best bet would be to get a pressure tester and set the lpr to the pressure listed in the pressure certificate that came with the marker, you can technically adjust the lpr to between 65-75psi, but bob long markers are really picky about pressures so the listed pressure should be the ideal pressure for your marker. If you do not have a pressure certificate I would just set the lpr to 75psi.



#3 Bunkee

Bunkee

    Newbie

  • Members
  • Pip
  • 4 posts

Posted 02 April 2014 - 02:17 PM

I have the tester and certificate the answer you gave me was perfect. Thanks Spart



#4 XGC_Cheevo

XGC_Cheevo

    Pod Scalping You

  • BST Moderator
  • PipPipPipPipPipPip
  • 2,848 posts
  • Gender:Male
  • Location:Mitchell, SD

Posted 02 April 2014 - 03:37 PM

Pressure tester + lurker method of sweetspotting.

 

Lurker method of sweetspotting regs.

1: Back out both regs or Zero out both the LPR and HPR to 0psi
2: Raise HPR slightly only to set LPR for cycling
3: Raise LPR to fully cycling ~45psi or so
4: Raise HPR until velocity begins to stop rising as you increase pressure
5: Raise LPR to desired velocity
6: Lower HPR a bit, then raise if necessary... you're trying to find the best HPR setting at the LPR setting you have. This may put your velocity over 300/285
7: Lower LPR slightly to field velocity

__________________


#5 BurningPlaydoh

BurningPlaydoh

    Blow-dough'ed

  • Members
  • PipPipPipPipPipPipPip
  • 5,806 posts
  • Gender:Male
  • Location:Twin Cities, MN

Posted 02 April 2014 - 04:03 PM

I would sweetspot using the method above and write down the pressures you end up with. Factory pressures could be a good bit off due to paint size being shot.

#6 Bunkee

Bunkee

    Newbie

  • Members
  • Pip
  • 4 posts

Posted 02 April 2014 - 04:48 PM

Do I need to adjust the dwell at all after completing lurker?



#7 Justin B.

Justin B.

    One Nation D5 EPL Paintball 2014!

  • Members
  • PipPipPipPipPip
  • 2,409 posts
  • Gender:Male


Posted 02 April 2014 - 05:06 PM

Do I need to adjust the dwell at all after completing lurker?

Nope, I highly suggest sweetspotting like the others have said. I had a Bob Long Vice and sweetspotting it made it shoot REALLY good.


One Nation

 

My Feedback: http://www.techpb.co...howtopic=210995

"CP anything should immediately reduce the value to zero, its painful to see nice guns with CP regs."

- Cookybiscuit


#8 SPARTAN1147789

SPARTAN1147789

    SPARTAN

  • Members
  • PipPipPipPip
  • 751 posts
  • Gender:Male

Posted 02 April 2014 - 06:30 PM

Yeah, if you want to make it as good as possible sweetspotting is best, I just think it's a lot easier just to go by the factory certified pressure.







Also tagged with one or more of these keywords: LRP, G6r, Bob Long, Pressure

1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users