Jump to content


Photo

trracer


  • Please log in to reply
6 replies to this topic

#1 BellaY

BellaY

    Sophomore Member

  • Members
  • PipPipPip
  • 489 posts
  • Gender:Male

Posted 13 September 2009 - 02:35 AM

i have a pmi trracer and it is leaking out the barrel. If i pump it the leak slows down alot, but still leaks. I do have a stiffer spring in there im thinking that could be a cause but im not sure

any help will be appreciated :lol:
Posted Image



#2 Leafy

Leafy

    Uses the Man Pedal

  • Members
  • PipPipPipPipPipPip
  • 4,836 posts
  • Gender:Male
  • Location:NH/MA

Posted 13 September 2009 - 10:02 AM

a stiffer main spring could defiantly cause it, run some oil through it dry firing and see if that clears it up though.

#3 ninjapaintball

ninjapaintball

    Senior Member

  • Members
  • PipPipPipPipPip
  • 1,891 posts
  • Gender:Male
  • Location:Crystal Lake, IL

Posted 13 September 2009 - 10:06 AM

i have a pmi trracer and it is leaking out the barrel. If i pump it the leak slows down alot, but still leaks. I do have a stiffer spring in there im thinking that could be a cause but im not sure

any help will be appreciated :lol:


The leak is cause by the hammer resting on the cup seal. Take apart the back end and check the cup seal rod as that part can come loose from the seal cup. Also clean the seat and seal area.
NINJA PAINTBALL - PROUDLY MADE IN THE USA
Ninja Paintball Factory Tech
If you have a question please post it in the NINJA/PSI GURU forum
DOT Certified Hydro Tester G777

#4 Leafy

Leafy

    Uses the Man Pedal

  • Members
  • PipPipPipPipPipPip
  • 4,836 posts
  • Gender:Male
  • Location:NH/MA

Posted 13 September 2009 - 10:07 AM

right I forgot that cup seal can get dirty if you use CO2, I've never run CO2 through my traccer, hence my forgettence.

#5 BellaY

BellaY

    Sophomore Member

  • Members
  • PipPipPip
  • 489 posts
  • Gender:Male

Posted 13 September 2009 - 03:20 PM

do you guys know if theres an online manual for the gun cuz im not familiar with the inside of the gun its my 3rd time taking it apart in over 10 years its simple to take apart but this a way i know if im missing somthing or not :o

Edited by BellaY, 13 September 2009 - 03:21 PM.

Posted Image



#6 ninjapaintball

ninjapaintball

    Senior Member

  • Members
  • PipPipPipPipPip
  • 1,891 posts
  • Gender:Male
  • Location:Crystal Lake, IL

Posted 13 September 2009 - 03:29 PM

do you guys know if theres an online manual for the gun cuz im not familiar with the inside of the gun its my 3rd time taking it apart in over 10 years its simple to take apart but this a way i know if im missing somthing or not :o


not that i am aware of. it is fairly simple
make sure no air
unscrew the back frame screw and remove the valve assembly
Unscrew the brass hex piece from the aluminum tube
clean the cup seal, seat and interior
make sure you tighten the rod to the seal retainer before reassembly
reassemble
NINJA PAINTBALL - PROUDLY MADE IN THE USA
Ninja Paintball Factory Tech
If you have a question please post it in the NINJA/PSI GURU forum
DOT Certified Hydro Tester G777

#7 Leafy

Leafy

    Uses the Man Pedal

  • Members
  • PipPipPipPipPipPip
  • 4,836 posts
  • Gender:Male
  • Location:NH/MA

Posted 13 September 2009 - 07:21 PM

and once you pull the back part out that holds the valve if you want to get all the rest of the internals out you just unscrew the pump handle from the bolt and everything else will slide out, or you might have to tap it a bit to get the bolt to come out.




2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users