Jump to content


Omerta

Member Since 29 Sep 2008
Offline Last Active Oct 16 2008 09:05 PM
-----

Topics I've Started

Help me pimp my cocker.

15 October 2008 - 05:43 PM

Hey guys.

I'm buying a 1999 Autococker on Friday (used).

Now, I love the mechanical aspect of Cockers, and want to keep it fully mechanical.

I don't know too much about Cockers, but I am looking to put the best (of the best) parts on it. Cost is not an issue.

What would you recommend?

Also, could anyone tell me if there are any aftermarket parts already on this Cocker?

Attached File  1f1126145ZZZZZZZZZ8a9ed2a5418d00513a6.jpg   7.1KB   36 downloadsAttached File  1f2122142ZZZZZZZZZ8a9132b0d0c8dd71df3.jpg   6.3KB   32 downloads

Thanks guys, look for the results!

The Ultimate 98 Upgrade Thread.

01 October 2008 - 03:52 PM

Accuracy
New Barrel - 8" is really short, but will get the job done. I would go with something between 12" and 14". Everything else is just overkill (I'm looking at you 20"ers).

HPA - HPA provides better consistency than CO2, thus a better velocity spread, which gives better accuracy.

Stabilizer - This "stabilizes" CO2 (hence the name) providing better consistency and a better spread. It basically helps it stay a gas, not liquid.


Efficiency
Polished internals - Smoother operation, and it's free...

Low Pressure Kit - A pricey package that helps lower you operating pressure.

Stabilizer - Like said before, stabilizes your CO2

Regulator - Allows you to adjust operating pressure.


Rate of Fire
E-Grip - Makes you marker electronic, lighter trigger pull, adjustable firing modes. It works by having a solenoid, that will move a pin, that will trip the sear, which will in turn, fire the gun. Some boards can cycle at 25CPS(Cycles Per Second), and others, 30 plus

Response Trigger - The Response Trigger(R/T) is a piston that resets the trigger, while you push on it. The time that you can hold your finger on the trigger with the right pressure, and get it going full auto(f/a), is the "Sweet Spot". Mine is pretty easy to obtain the sweet spot, but others may have trouble. It all has to do with the tuning. It is tuned by turning that screw above the right grip until it gets the best response. This will work with Compressed air, but can be a ***** to tune.

Cyclone feed
- Gives you the miracle of the A-5, a loader powered by excess CO2 that turns a "cyclone" to load balls into your gun. It turns with each shot. There are many mods, but it can only max at 23-25BPS.

Agitating/Forcefeed Hopper - For all you non-A5 users, will feed balls faster into your marker by using an impeller(a wheel, much like the Cyclone's, that has paddles on it) to feed the balls. They feed much faster than any other.

Centerfeed
- Allows faster feeding by mounting your feedneck vertically. Permanent mod, and requires you to send you gun into whoever makes it(I think Rufus Dawg).

New Trigger - Pointlesss unless you have an E-grip, then you can buy something that's walkable. APE makes a magnetic trigger, that is very walkable.


Comfort
New Grips - Gives you a better, more cushy grip. Or a new look. YOUR 98 IS A 45 GRIP FRAME. A-5's cannot use aftermarket grips. That goes for X-7's and Triumphs.

New trigger - Sometimes a double trigger just feels nice.

Drop Forward - Moves the tank forward and down for better balance.

Remote Line - Takes that cumbersome tank off your gun altogether, and will let you put your tank on your back...you do need a pack that will hold it. THIS CANNOT BE USED WITH AN ANTI-SIPHON TANK...THE TUBE WILL ACT LIKE A SIPHON TUBE.

Stock - Gives you a better shooting platform, and is usually used for guns with a Remote.

Omerta's Moderator Application

01 October 2008 - 03:04 PM

1) Name, Age, Location

My name is William, I am 21 years old, and I currently reside in Brooklyn New York.


2) Years of paintball experience

I have about 3-4 years of paintball experience.


3) Are you familiar with IP Board

Yes, I am. I have worked with it before.

4) What other message boards have you moderated, started, or assisted with

I have moderated and or administrated pbguns.net, and megafanclubforums.megadeth.com.


5) What sections would you like to help the TechPB community out with?

It honestly doesn't matter to me, I would just like to help out anywhere I can.


6) Have you ever worked at a paintball store, field, or within the industry?

Yes, I have. I've worked in a local paintball shop, and I was in charge of sales, and repairs.


7) Have you played in any major events? Scenario Games, National Tournaments, etc?

I play in all of Skirmishes big scenario game, and I plan to attend then next Oklahoma D-Day.


8) Any other forums you currently moderate at?

At the moment no, so if I was to be considered for a moderation position here at TechPB I would be able to dedicate my time here.

9) Fill out an employment application, send us a copy of your valid drivers license and consent to background check.

Will do so upon request.


Thank you Mike, and all those at TechPB.
I hope we can work together.

Woodsballers Unite!

29 September 2008 - 07:36 PM

If you're a true woodsballer post your name, gun of choice, and location here.

Name: Bill

Gun Of Choice:
Tippmann 98 Custom w/
Polished Internals
Cut Grip Frame
Cyclone Feed
Lapco Ratchet
Wargear Squishy Paddles
New Designs QEV
New Designs Hot Rod
BT Apex Tip
Lapco 12-inch BigShot
OPSGEAR AK47 Stock
DOP Powertube
DOP Front Bolt
TechT Trigger Pin Kit
Lapco Raised Sight Rail
NewStar 4X12 Scope
DOP Rocket Cock
Double Trigger (Unknown Brand)

Location: Brooklyn, NY