Jump to content


Yoda

Member Since 25 Sep 2008
Offline Last Active Jan 13 2009 05:13 PM
****-

Topics I've Started

Ranjerz cup video and rotor

28 October 2008 - 01:54 PM

**** I AM NOT A GOOD PHOTOGRAPHER, I HAVE NEVER DONE THIS BEFORE, THIS IS MY FIRST VIDEO, DON'T TELL MY I SHOULD HAVE BEEN INSIDE THE NET OR HOLD THE CAMERA STILL, I DID THIS WITH IMOVIE AND IT IS VERY HARD TO WORK WITH, I WILL MAKE A BETTER ONE LATER THIS WEEK ****


my rotor
http://s238.photobuc...nt=M2U00113.flv

Woot off!

22 October 2008 - 02:12 PM

its on!
the woot.com

DP marker UPGRADES!

12 October 2008 - 12:14 PM

G3:
APE STOCK replacement board
APE upgrade board
G3 Replacement trigger
TechT L7 Bolt
Any .45 grips-Virtue are tight, may need to cut
TBO trigger

Threshold:
none right now
Ape board soon
Any threshold/F7/F8 grips

F7:
Fusion Hyper Colour kit*
Hyper trigger
Any threshold/F7/F8 grips
SD board
Virtue board
APE board soon
Eigen ram
Violent bolt
ACP bolts
ACP ram
Boss bolt

F8:
Any threshold/F7/F8 grips
SD board
Virtue board
APE board soon
Eigen ram
Violent bolt
ACP bolts
ACP ram
Boss bolt
Gauge*

All:
Virtue lazer eyes-very tight on thresholds, do NOT suggest to get if you have a threshold
SD eyes-long, fit any DP marker
Any ASA, some may need a new rail as well
Any cocker threaded barrel
Any matrix threaded feedneck
Any reg but the PM8, DM8 and DM9

*=can be found under DP shop
DP SHOP

Full pics of 09 PE guns!

05 October 2008 - 09:21 PM

Yeah...
Posted ImagePosted Image
Posted Image
Posted Image
Posted Image
Posted Image

DP marker troubleshooting

30 September 2008 - 03:35 PM

Most of the DP markers are similar in a few types of issues, so read this for any problem.

First, change your battery! Even if it was just put in, try a brand new name brand battery.
All of these are to be used after you have tryed a new battery.

G3:
FSDO-Lube lightly with dow 33, or any other paintball lube, hater, lurker etc
Leak from inside trigger frame: Lube the noid lightly with dow 33
Trigger bounce: Adjust trigger so it trips the switch in about the middle, not in the beginning or end
Eye issue: Make sure both eyes are plugged in and no wires are pinched, and are correctly aligned

F8/7:
Leak from breech: Lube valve and poppet, check to make sure valve is still intact
Leak from inside trigger frame: Lube the noid lightly with dow 33
Drop off: Lube HPR(LPR too for F7), lube ram, make sure your tank is fully screwed in
Trigger bounce: Adjust trigger so it trips the switch in about the middle, not in the beginning or end
Eye issue: Make sure both eyes are plugged in and no wires are pinched, and are correctly aligned


Threshold:
FSDO-Lube lightly with dow 33, or any other paintball lube, hater, lurker etc
Leak from inside trigger frame: Lube the noid lightly with dow 33
Trigger bounce: Adjust trigger so it trips the switch in about the middle, not in the beginning or end
Eye issue: Make sure both eyes are plugged in and no wires are pinched, and are correctly aligned


Will add more when they arise, this will greatly help the "help me" threads I think.